Baumr-AG SS16 User Manual Download | Manualshive

Page: 10 / 15

background image

Scroll Saw - SS16

E&OE

© 2017 Baumr-AG

10

Power Switch and Speed Control

To avoid injury from accidental start-ups, always switch the machine OFF and disconnect it
from the electrical supply before moving it, replacing the blade, or making adjustments

. •

Always wait for the saw to come to a complete stop before restarting.

To switch the machine ON:

•

Press the green ON ("I) button.

To switch the machine OFF:

•

Press the red OFF ("O") button.

To adjust speed (strokes per minute / SPM):

Speed is adjustable between 400 and 1600 SPM. Rotate the speed control
right (clockwise) to increase speed; rotate left (anti-clockwise) to reduce speed.

Freehand Cutting

(Fig. 17)

1. Raise the blade guard foot (

1

) by loosening the height

adjustment knob (

2

).

2. Position the work-piece against the blade and place the

blade guard foot against the top surface of the work-piece.

3. Secure the blade guard foot (

1

) by tightening the height

adjustment knob (

2

).

4. Remove the work-piece from the blade prior to switching

the machine ON.

5. Slowly feed the work piece into the blade by guiding and

pressing the work piece down against the table.

6. When the cut is complete, move the trailing edge of the

work piece beyond the blade guard foot.

Angle Cutting (Bevelling)

(Fig. 18)

1. Move the blade guard foot to the highest position by

loosening the height adjustment knob (

1

). Re-tighten the

knob.

2. Tilt the table to the desired angle by loosening the table

bevel lock knob (

2

). Move the table to the required angle

using the degree scale and the pointer (

3

).

3. Tighten the table bevel lock knob (

2

).

4. Loosen the blade guard screw, and tilt the blade guard to the

same angle as the table. Re-tighten the blade guard screw.

5. Position the work piece on the right side of the blade. Lower

the blade guard foot against the surface by loosening the
height adjustment knob. Re-tighten the knob.

6. Slowly feed the work piece into the blade by guiding and pressing the work piece down against the table.

7. When the cut is complete, move the trailing edge of the work piece beyond the blade guard foot.

3

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BAUMR-AG BAUMR-AG BAUMR-AG BAU

MR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

«
...
8
9
10
11
12
...
»

Summary of Contents for SS16
















Reviews:

No comments

Related manuals for SS16

Brand: Yard force Pages: 150

Brand: Rikon Power Tools Pages: 40

Brand: Zenoah Pages: 7

Brand: 909 Pages: 20

McDonnell & Miller RB-24E-S

Brand: Xylem Pages: 8

Brand: Target Pages: 52

Craftsman 113.23161

Brand: Sears Pages: 36

Brand: King Industrial Pages: 5

Brand: Jet Pages: 32

Brand: Maktec Pages: 12

Brand: Performax Pages: 20

Brand: Scheppach Pages: 92

Brand: Makita Pages: 48

Brand: F.F. Group Pages: 72

Brand: Astro Pneumatic Pages: 4

Brand: Whirlwind Pages: 29

Brand: terrasaw Pages: 18

Brand: Mac Afric Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands