background image

Do 

get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by
heat. They may, therefore, scorch or become discoloured when close to a heating 
appliance. Please bear this in mind whenever you are considering redecorating.

Do 

provide a minimum side clearance as detailed below:

The minimum allowable distance from the outside of the fascia to a corner wall having
combustible material or any other combustible surface which projects beyond the front
of the appliance is 100mm. 
For access purposes a 10mm clearance to non-combustible surfaces is recommended on
the left side of the appliance, on the right side the recommended clearance is 50mm  for
access to the slider control.
Please bear this in mind if ever you are altering the room.

Don’t 

hang clothing, towels or any other fabrics over the fire.

Don’t 

put more ceramic fuel effect pieces on the fire than the number given in this

guide or use any ceramic fuel effect pieces other than those authorised for this fire.
Incorrect combustion could result.

Don’t 

put paper or other materials onto your fire.

Don’t 

use the fire with damaged base ceramics. 

Don’t 

place any combustible material (rugs, carpet, plastic tiles, etc.) on the hearth

Don’t 

attempt to clean or service the fire until it has been switched off and allowed to 

cool completely.

GAS CONSUMPTION

Model 750

Has a maximum natural gas input of 6.0kW (Gross)
Has a maximum natural gas output of 3.1kW 

Has a minimum natural gas input of 2.7kW (Gross)
Has a minimum natural gas output of 1.3kW 

Model 750 when converted using kit number 0595221 

Has a maximum propane gas input of 6.1kW (Gross)
Has a maximum propane gas output of 3.1kW 

Has a minimum propane gas input of 4.3kW (Gross)
Has a minimum propane gas output of 2.1kW 

Page 5

OWNER GUIDE

Summary of Contents for 750FS











Reviews: