Baxi Nuvola 3 Comfort Operating And Installation Instructions Download

Page: 27 / 40

C607215 - GB

INSTRUCTIONS FOR FITTERS

21. PARAMETERS SETTING

To set the boiler parameters, proceed as follows:

• press the key

for at least three seconds ;

• press and hold down the key

and then press

(see figure at side). When the function

is active, the letters “F01” and the value of the selected parameter appear on the display.

Changing the parameters

•

Press the

+/-

buttons to scroll through the parameters;

•

Press the

+/-

buttons to change each parameter value;

NOTE:

the value is automatically memorised after about 3 seconds. (Do not press any key until the value starts to flash).

0607_1908

Factory settings

Description of parameters

140 Fi 240 Fi

280 Fi 320 Fi

240 i

280 i

F01

Type of boiler

= sealed chamber -

= atmospheric chamber

F02

Gas used

NATURAL (METHANE) - 01 = LPG

00 or 01

F03

Hydraulic system

F04

Setting programmable relays 1

= zone system (See SERVICE Instructions)

F05

Setting programmable relays 2

= “cool” function for external conditioning system

(See SERVICE Instructions)

F06

Configuration of external probe inlet

(See SERVICE Instructions)

F07…F09

Manufacturer’s information

Mode of installing the climate controller

F10

= on the wall (paragraph 18.2)

= Not used

= in the boiler (paragraph 18.1)

F11…F12

Manufacturer’s information

F13

Max heating power

(0-100%)

100

F14

Max DHW power

(0-100%)

100

F15

Min heating power

(0-100%)

F16

Setting of maximum heating setpoint (°C)

= 85°C -

= 45°C

F17

Pump post-circulation time in heating (01-240 minutes

)

F18

Waiting time in heating before a new ignition

(00-10 minutes) - 00=10 seconds

F19

Manufacturer’s information

F20

Manufacturer’s information

F21

Anti-legionella function

= Disabled

= Enabled

F22

Manufacturer’s information

F23

Maximum DHE setpoint temperature (ACS)

F24

Manufacturer’s information

F25

Protection device against water lack

F26…F29

Manufacturer’s information (read-only parameters)

F30

Manufacturer’s information

F31

Manufacturer’s information

F32…F41

Diagnostics (See SERVICE Instructions)

last

Activation of calibration function

parameter

(See SERVICE Instructions)

ATTENTION: do not change the value of the “Manufacturer’s information” parameters

Summary of Contents for Nuvola 3 Comfort









































Search results

Summary of Contents for Nuvola 3 Comfort

Reviews:

Related manuals for Nuvola 3 Comfort

Brands by name

Popular brands

Baxi Nuvola 3 Comfort, Operating And Installation Instructions

Search results

Summary of Contents for Nuvola 3 Comfort

Reviews:

Related manuals for Nuvola 3 Comfort

Brands by name

Popular brands