background image

Manual breast pump

EN

7

 

Place the breast pad A

2

 against the breast in such a way that the nipple is located in the middle of the 

breast pad A

2

 . Use your thumb and index finger to hold the breast pad A

2

 against the breast and use 

the palm of the same hand to support the breast . The breast pad A

2

 must perfectly adhere to the breast .

 

Press the handle A

qa

 and then release it slowly . At the same time, press the breast flange A

2

 gently against 

the breast so that it is tightly seated and no air is drawn in . 

 

You can change the expression phase intensity at any time as required so that the expression is as pleasant 
as possible for you as described in chapter Using the breast pump – Setting the expression phase and 
intensity .

 

After you have finished expressing milk, place the breast pump with the feeding bottle A

qd

 into the bottle 

stand A

qg

 . The breast pump must not be tipped over, milk could flow out . Ideally, immediately upon finishing 

expressing milk, remove the bottle A

qd

 with milk out of the breast pump body A

3

 . 

 

Screw the bottle opening cap A

6

 with the nipple A

5

 on to the bottle A

qd

 if you wish to feed the expressed 

milk immediately or close it according to the instructions contained in the chapter Assembling and 
disassembling feeding bottles . 

Note:

To prevent spillage, do not fill the feeding bottle A

qd

 with more than 140 ml of milk .

 

Clean all used parts according to the instructions in chapter Cleaning and sterilisation .

Tips and advice for using the breast pump 

 

If you feel an unpleasant pressure, lower the expression intensity .

 

You can express milk first from one breast and then continue expressing milk from the other breast . 

 

If you are not successful expressing any milk within the time interval of approx . 5 minutes, stop the breast 
pump . First try relaxing for a while and warm the breasts up in a warm shower . Then try again to express the 
milk or postpone it to a later time when more milk has been created .

 

Usually, 10 minutes should be sufficient to express the milk . This time is only indicative and may vary from 
person to person .

Storing and heating up breast milk 

 

Only breast milk collected using a clean and sterilised breast pump is suitable for storage . Store the milk 
in sterilised containers designed for storing breast milk or in special disposable breast milk storage bags .

 

To prevent the milk from leaking or absorbing other odours from an area in which it is stored, thoroughly 
close containers or bags before placing them in the refrigerator or freezer .

 

Breast milk can be stored for up to 48 hours in a refrigerator (except for the door area) and up to 3 months 
in a freezer at a temperature of -18 °C .

 

If you express the milk gradually and wish to mix the individual batches together into a single container and 
freeze them, do so no later than within 24 hours . It is only possible to mix batches that are cooled to the 
same temperature .

 

Mark the containers or bags that you place in the freezer with a date .

Note

The feeding bottle A

qd

 can be stored in a refrigerator or freezer .

Summary of Contents for BBP 1000










Reviews: