Bayrol Auromatic Salt Instructions For Use Manual Download

Page: 30 / 56

Outdoor pool

Indoor pool

The following water values must be set step by step in the pool water before the Automatic

SALT

is put into operation:

Water values

Step

Salt level

(g/l)

Alkalinity/TAC

(mg/l)

pH value

(pH)

Stabilizer

(mg/l)

Chlorine DPD1

(mg/l)

Tolerable values

1.5 – 40

Min. 80

7.0 – 7.4

30 – 50

1.2 – 3.5

Not needed

0.5 1.5

Recommended
values

1.5 – 5.0

Min. 80

7.2

ca. 40

1.5 – 3.0

Not needed

0.6 1.2

To increase

Add salt

Add BAYROL

AlcaPlus

Add

pHPlus

Add BAYROL

Stabichloran

Boost/

Add chlorine

manually/

Increase

production rate

To lower

Drain pool partly

and refill

with fresh water

–

Add

pHMinus

Liquid Anti Calc

Drain pool partly

and refill with fresh

water

Lower

production

rate of cell

Test during
the season

After refilling the

pool and after the

filter backwash

monthly

weekly

monthly

weekly

To save time when setting the values, you can carry out
steps 1 – 4 simultaneously.
Make sure you start with step 5 not before the pH value is
set.
In outdoor pools additionally the stabilizer needs to be
added before dosing chlorine.
Set the desired chlorine value for operation already now.
It is essential that this value is set correctly at the time of
commissioning the Automatic

SALT

RECOMMENDATION

To effectively prevent possible calcification of the chlorine
generation cell caused by the system, it is recommended to
add BAYROL Calcinex

(300 ml/10 m³) to the pool water.

The risk of calcification can be further reduced by using
pHMinus Liquid Anti Calc! The highly recommended addi
tion of Calcinex

(see below) can be carried out at any time.

Please note

The consistent use of Calcinex

and pHMinus Liquid

Anti Calc can extend the lifetime of the cell!

Please follow the general instructions below when carrying
out the adjustment of the values in the pool water:

–

Always determine the respective values of the pool water

before starting to adjust the value.

–

Make sure that the pool water is free of dissolved metals.

Make sure that this is also the case for the entire operat
ing time of the pool.

–

Calculate the amount of water treatment product required

to achieve the desired value before adding it. Consult the
dosing instructions of the respective water care product.

–

Always add the respective products to the pool water

gradually and always with the circulation running. Open all
inlets and outlets including the floor drain.

–

Find a place in the pool with the best possible flow for the

addition, e.g. from the inlet nozzles or directly into the
skimmer. This way you will achieve a complete dissolution
of the added water care products and an even distribu
tion. Let the circulation run for 1 hours even after the last
water value has been reached to ensure complete mixing.

–

Occasional measurements during the addition of the

respective water care products can help to prevent over
dosing.

Additional instructions

For Step 1: Adding the salt

Add the salt granules directly to the pool. To do this, find
a place in the pool where there is high flow, e.g. at the inlet
jets. It is best to additionally swirl the salt with a brush
with a long handle to accelerate the dissolving process.

IMPORTANT

Please use only salt approved for use in swimming pools!
Choose salt in form of granules for faster solubility. The
amount of salt required to achieve the desired salt content
can easily be determined using the formulas given in the
annex.

For Step 5: Manual adding of chlorine

When adding chlorine manually, please ensure that the
chlorine is completely dissolved and mixed in the pool
water before measuring the chlorine level manually.

IMPORTANT

For a quick increase of the chlorine level in the pool,
Chloryte

is best suited. Alternatively, Chlorifix

can be

used also.