background image

7

ENGLISH

FRANCAIS

SP

ANISH

DEUT

SCH

Specifications

Here you will find a number of fault description and possible 

solutions we invite you to read in order to ensure the possibility 

of an actual breakdown of your device.

The unit does not turn on

- Make sure the power cord is properly connected.

- Make sure the plug is fully inserted into the wall outlet and 

there is power.

- Make sure the amplifier is turned on.

- Check the fuse in the mains plug or adapter if necessary.

Troubleshooting

There is no sound

- Make sure the unit is not in Standby mode.

- Check that the source component is connected properly.

- Make sure your speakers are properly connected.

One channel no sound

- Make sure the balance control is in the correct position.

- Check the speaker connections.

- Check interconnections.

A loud humming or buzzing is noticeable

- Make sure that interconnect cable is loose or defective.

- Make sure your tape deck or turntable is not too close to the 

amplifier.

The bass is weak or the stereo image is diffuse

Make sure the speakers are not in phase.

The sound is distorted

Make sure that the control settings of volume or tone is not too 

high.

The remote control does not work

- Check that the batteries have not expired.

- Make sure nothing is blocking the remote sensor.

In case the above solutions do not remedy your problem, check 

our FAQ section (Frequently Asked Questions) on our website: 

www.bc-acoustique.com

For  repair,  during  or  after  the  warranty,  please  contact  your 

dealer.

To  obtain  warranty  service  and  technical  support,  thank 

you  kindly  to  register  your  product  online  on  the  website                          

www.bc-acoustique.com at the product registration section.

Troubleshooting

Preamplifier section

Line level inputs (LINE 1 to LINE 3)

Sensitivity: 200 mV

Impedance: 50 pF kOhms/100

Maximum input level: 7 V

Corrections

Bass (± 10 dB at 100 Hz)

Treble (± 10 dB at 10 kHz)

Amplifier Section

Continuous average power into 8 ohms: 2 x 70 W

Continuous average power into 4 ohms: 2 x 120 W

Distortion: 0.01% (20 Hz - 20 kHz)

Signal / noise ratio: 100 dBA

Connector WIRELESS, 

to  use  with  your  Smartphone,  tablet,  

computer or other WIRELESS devices.

Connectors Front side

1x Headphone output (jack 6.35mm)

1x MP3 input (jack 3.5mm) for portable audio player

Connectors Rear side

3x Line inputs (LINE 1 to LINE 3)

1x Optical Input

1x Coaxial Input

Speaker terminals screw-compatible banana plugs

General

Detachable power cable

UNIT

Dimensions (W×H×D) with stand: 430 x 80 x 320 mm

Weight: 8.3 kg

Dimensions (W×H×D) without feet: 430 x 70 x 320 mm

Weight: 8.2 kg

BOX

Dimensions (W×H×D): 490 x 140 x 385 mm

Weight: 8.9 kg

Volume: 0.03 m

3

EX222.3 EAN CODE: 0634654606112

  

 

BC ACOUSTIQUE

  

 

BP 306

  

 

94709 Maisons-Alfort Cedex France

  

 

www.bc-acoustique.com

Summary of Contents for EX222.3









Reviews: