background image

10

Here you will find a number of fault description and possible 

solutions we invite you to read in order to ensure the possibility 

of an actual breakdown of your device.

The unit does not turn on

- Make sure the power cord is properly connected.

- Make sure the plug is fully inserted into the wall outlet and 

there is power.

- Make sure the amplifier is turned on.

- Check the fuse in the mains plug or adapter if necessary.

There is no sound

- Make sure the unit is not in Standby mode.

- Check that the source component is connected properly.

- Make sure your speakers are properly connected.

One channel no sound

- Make sure the balance control is in the correct position.

- Check the speaker connections.

- Check interconnections.

A loud humming or buzzing is noticeable

- Make sure that interconnect cable is loose or defective.

- Make sure your tape deck or turntable is not too close to the 

amplifier.

The bass is weak or the stereo image is diffuse

Make sure the speakers are not in phase.

The sound is distorted

Make sure that the control settings of volume or tone is not too 

high.

The remote control does not work

- Check that the batteries have not expired.

- Make sure nothing is blocking the remote sensor.

WIRELESS - The sound stops or there is noise

If  a  device  such  as  a  microwave  oven  or  wi-fi  transmitter  

generates electromagnetic waves near the 2.4 GHz band, it can 

affect the connection or broadcast quality. In this case, install 

the EX-242 at a greater distance from this unit.

WIRELESS - The transmission is interrupted

- The device connected to the EX-242 is perhaps too far. The 

approximate  distance  transmission  WIRELESS  is  about  10m  

without obstacles.

-  Make  sure  there  are  no  obstacles  between  the  EX-242  and 

your WIRELESS device.

Troubleshooting

In case the above solutions do not remedy your problem, check 

our FAQ section (Frequently Asked Questions) on our website: 

www.bc-acoustique.com

For  repair,  during  or  after  the  warranty,  please  contact  your 

dealer.

To  obtain  warranty  service  and  technical  support,  thank 

you  kindly  to  register  your  product  online  on  the  website                          

www.bc-acoustique.com at the product registration section.

  

 

BC ACOUSTIQUE

  

 

14 Avenue de l'Europe

  

 

77600 Bussy Saint-Georges - France

  

 

www.bc-acoustique.com

Summary of Contents for EX242













Reviews: