background image

BI250-945GSE

 

 

 

HDD Bracket  

 

 

 

Package Contents:

 

 

 

 

One 

BI250-945GSE

 

 

 

One 

Driver CD/DVD

 

One 

User’s Quick Start Card

 

 
 

 

 
 
 
 
 
 
 

Inside the BI250-945GSE 
 

 

One 

MX945GSE4 Motherboard

 

 

 

One 

SATA & Power Cable

 

One 

HDD Bracket

 

SATA & Power cable 

MX945GSE4

 

 

BI250-945GSE 

Intel

®

 Atom™ N270 Processor  

User’s Quick Start Card

  

 

Version 1.2

 

 

http://www.bcmcom.com 

 

Responsibility: 

This manual is provided “As-Is” with no warranties of any kind, expressed or implied, including, but not limited to the 
implied warranties or conditions of this product’s fitness for any particular purpose. In no event shall we be liable for any 
loss of profits, loss of business, loss of data, interruption of business, or indirect, special, incidental, or consequential 
damages of any kind, even the possibility of such damages arising from any defect or error in this manual or product. We 
reserve the right to modify and update the user manual without prior notice. 

 

 

WARNING: CMOS Battery Damage

 

Replace your system’s CMOS RAM battery only with the identical CR-2032 3V Lithium-Ion coin cell (or equivalent) battery 
type to avoid risk of personal injury or physical damage to your equipment. Improper installation might cause battery to 
explode. Always dispose of used batteries according to the manufacturer’s instructions, or as required by the local 
ordinance (where applicable).  The damage due to not following this warning will void your motherboard’s manufacturer 
warranty. 
 
Perchlorate Material- Special Handling May Apply. 
See 

http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

 

 

 

Additional Information: 

Additional information on setting the motherboard up can be found in the MX945GSE4 User’s Manual in the provided CD 
or DVD ROM.  The Online User’s Manual and FAQ/Knowledge Base can be found on our website by visiting our website: 

http://www.bcmcom.com

.  If your question is not answered in our FAQ/Knowledge Base, visit our forums and post your 

messages or submit a new FAQ through FAQ Submittal form for us to add your question in our FAQ with our answer. 

 

 

 

ATTENTION: Incorrect BIOS Setup

 

If you do not know how to handle BIOS setup or how to set it up properly, it is strongly advisable that you do not modify 
any of the settings than otherwise instructed in the User’s Quick Start Card.  Even a seemingly small incorrect adjustment 
or modification in the BIOS setup can render your system unstable or unusable. Incorrect BIOS setup is not covered by 
your motherboard’s manufacturer warranty. Try Clear CMOS information when system does not boot after BIOS settings 
change.

 

 

Summary of Contents for BI250-945GSE

Page 1: ...ause battery to explode Always dispose of used batteries according to the manufacturer s instructions or as required by the local ordinance where applicable The damage due to not following this warning will void your motherboard s manufacturer warranty Perchlorate Material Special Handling May Apply See http www dtsc ca gov hazardouswaste perchlorate Additional Information Additional information o...

Page 2: ... 5 6 PINIT PRND2 7 8 LPT_SLIN PRND3 9 10 GND PRND4 11 12 GND PRND5 13 14 GND PRND6 15 16 GND PRND7 17 18 GND ACK 19 20 GND BUSY 21 22 GND PE 23 24 GND SLCT 25 26 KEY SPI JSPI1 Power in JPW1 Power Out JPWR1 S PDIF JSPDO1 Audio JAUD1 Signal Pin Pin Signal VCC3_SB 1 2 VCC3_SB SPI_MISO_F 3 4 SPI_MOSI_F SPI_CS0_F 5 6 SPI_CLK_F GND 7 8 GND SPI_HOLD 9 10 KEY Pin Signal 1 12V 2 12V 3 GND 4 GND Pin Signal ...

Page 3: ...ll them Touch a grounded surface before you remove any system component from its protective anti static packaging Unpacking and installation should be done on a grounded anti static mat The operator should be wearing an anti static wristband grounded at the same points as the anti static mat During configuration and installation touch a grounded surface frequently to discharge any static electrica...

Page 4: ...he base Figure 1 Figure 1 Unscrew 4 screws 1 3 Unscrew 4 flat head screw and lift out HDD assembly Figure 2 1 3 1 Remove or add notebook HDD from or to HDD bracket Figure 3 Figure 2 Removal of HDD Figure 3 Removal of HDD ATTENTION System Orientation Due to fire safety reasons the system should be oriented horizontally If used vertically it must be oriented in the position intended for a VESA mount...

Reviews: