21
Fill Hydraulic Oil
The log splitter is shipped without hydraulic fluid in the reservoir. Fill the reservoir before your initial use.
1. Remove the vented reservoir dipstick, which is located next to the engine on top of the reservoir tank.
See FIGURE 14.
2. Slowly fill the reservoir with the recommended hydraulic oil until oil level reaches the maximum line on the dipstick.
3. Replace the vented dipstick in the reservoir.
4. Start the engine, and use the control handle to engage the wedge to the farthest extended position and then
retract. Repeat this operation for 12 cycles. Much of the fluid will be drawn into the cylinder and hoses. Stop the
engine, and check the oil level as instructed below.
NOTE:
Make sure the oil level is above the bottom line on the dipstick. If not, refill the reservoir to prevent damage
to the hydraulic pump. DO NOT overfill. Some fluid may overflow from the vent plug as the system builds heat and
the fluid expands and seeks a balanced level.
5. However, you MUST check the fluid level before each operating. If not filled, proceed with above steps.
Page 18
Fill hydraulic oil
The log splitter is shipped without hydraulic fluid in the reservoir. Fill the reservoir before your initial use.
1. Remove the vented reservoir dipstick, which is located next to the engine on top of the reservoir tank.
See FIGURE 14.
0
°
10
°
20
°
30
°
40
°
50
°
60
°
70
°
80
°
90
°
(-18°) (-12°) (-7°) (-1°) (4°) (10°) (16°) (21°) (27°) (32°)
2. Slowly fill the reservoir with the recommended hydraulic oil until oil level reaches the maximum line on the dipstick.
3. Replace the vented dipstick in the reservoir.
4. Start the engine, and use the control handle to engage the wedge to the farthest extended position and then retract.
Repeat this operation for 12 cycles. Much of the fluid will be drawn into the cylinder and hoses. Stop the engine, and
check the oil level as instructed below.
NOTE:
Make sure the oil level is above the bottom line on the dipstick. If not, refill the reservoir to prevent damage to
the hydraulic pump.
DO NOT overfill.
Some fluid may overflow from the vent plug as the system builds heat and the
fluid expands and seeks a balanced level.
5. However, you
MUST
check the fluid level before each operating. If not filled, proceed with above steps.
(FIGURE14)
Page 21
ISO 68
ISO 46
ISO 32
ISO 22
Please select the oil based on the outside
temperature range the log splitter will be used in.
Refer to the chart provided to select the appropriate
hydraulic oil.
Approved fluids include Shell Tellus® S2 M 32
Hydraulic Fluid, Dexron® III / Mercon® automatic
transmission fluid, Pro-Select™ AW-32 Hydraulic Oil
or 10WAW-ISO viscosity grade 32 hydraulic oil. It is
not recommended that fluids be mixed, to top off the
reservoir tank during initial set-up use Shell Tellus®
S2 M 32 Hydraulic Fluid only.
Page 18
Fill hydraulic oil
The log splitter is shipped without hydraulic fluid in the reservoir. Fill the reservoir before your initial use.
1. Remove the vented reservoir dipstick, which is located next to the engine on top of the reservoir tank.
See FIGURE 14.
0
°
10
°
20
°
30
°
40
°
50
°
60
°
70
°
80
°
90
°
(-18°) (-12°) (-7°) (-1°) (4°) (10°) (16°) (21°) (27°) (32°)
2. Slowly fill the reservoir with the recommended hydraulic oil until oil level reaches the maximum line on the dipstick.
3. Replace the vented dipstick in the reservoir.
4. Start the engine, and use the control handle to engage the wedge to the farthest extended position and then retract.
Repeat this operation for 12 cycles. Much of the fluid will be drawn into the cylinder and hoses. Stop the engine, and
check the oil level as instructed below.
NOTE:
Make sure the oil level is above the bottom line on the dipstick. If not, refill the reservoir to prevent damage to
the hydraulic pump.
DO NOT overfill.
Some fluid may overflow from the vent plug as the system builds heat and the
fluid expands and seeks a balanced level.
5. However, you
MUST
check the fluid level before each operating. If not filled, proceed with above steps.
(FIGURE14)
Page 21
ISO 68
ISO 46
ISO 32
ISO 22
Please select the oil based on the outside
temperature range the log splitter will be used in.
Refer to the chart provided to select the appropriate
hydraulic oil.
Approved fluids include Shell Tellus® S2 M 32
Hydraulic Fluid, Dexron® III / Mercon® automatic
transmission fluid, Pro-Select™ AW-32 Hydraulic Oil
or 10WAW-ISO viscosity grade 32 hydraulic oil. It is
not recommended that fluids be mixed, to top off the
reservoir tank during initial set-up use Shell Tellus®
S2 M 32 Hydraulic Fluid only.
