BEA Br3 User Manual Download

Page: 15 / 15

9 Company Contact

Do not leave problems unresolved. If a satisfactory solution cannot be achieved after troubleshooting a problem, please

call BEA, Inc. If you must wait for the following workday to call BEA, leave the door inoperable until satisfactory repairs

can be made. Never sacrifice the safe operation of the automatic door or gate for an incomplete solution.

The following numbers can be called 24 hours a day, 7 days a week. For more information, visit www.beasensors.com.

East:

Canada and Texas:

1-866-249-7937

1-866-836-1863

Central:

West:

1-800-407-4545

1-888-419-2564

PROBLEM

PROBABLE CAUSE

CORRECTIVE ACTION

Module will NOT react to any input. 1. Incorrect Br3 power

2. Module not programmed

3. Incorrect wiring

4. Faulty module

1. Check the Br3’s power. It should be 12 to 24 volts AC or DC +/- 10%.

Ensure that input power is applied at the correct terminals.

2. Ensure a function has been programmed. If ‘

‘ is showing in the

display, the Br3 will need to be programmed.

3. Jumper an active Input and ensure that the fault is not within the wiring.

If module works when jumped, trace wiring from Inputs / relays.

4. Replace module.

Module reacts to input but has no

output.

1. Wrong outputs are

connected

2. Incorrect wiring

3. Incorrect jumper settings

4. Faulty module

1. Check to ensure that the proper outputs are connected per the function

selected.

2. Trace all wiring to ensure correct termination points.

3. Check that the jumpers are configured correctly for the application.

4. Replace module

8 Troubleshooting

1. Document all work. For future reference, be sure to record the Br3 Serial Number on your Work Order.
2. Educate the Owner / Manager as to the proper operation of the door and sensor system, and what to do to ensure safe use of the door in the

event of discovering a malfunction. Show the Owner / Manager how to perform a daily safety check of the system. You may also wish to provide

the owner/Manager a copy of an owners manual provided by AAADM for the type of door selected.

3. Be sure to obtain signatures on your work order for all work accomplished.

7 Documentation

Page 15 of 15

75.5501.02 EN 20091102 (75.5500)

Summary of Contents for Br3
















Search results

Summary of Contents for Br3

Reviews:

Related manuals for Br3

Brands by name

Popular brands

BEA Br3, User Manual

Search results

Summary of Contents for Br3

Reviews:

Related manuals for Br3

Brands by name

Popular brands