BEA LZR-H110 User Manual Download

Page: 3 / 12

75.5897.02 LZR-H110 20170821

Page 3 of 12

2
3
4
5

DESCRIPTION

SYMBOLS

LED SIGNAL

DETECTION LEDs

no detection

ERROR LED

POWER LED

detection

no error

error

no power

power

Caution!

Laser radiation

LED flashes quickly

LED flashes

LED is off

laser sweep emission

laser sweep reception

LED signal (4)

screw for position lock (2)

connector

protection cover

visible laser beam (3)

notch for tilt angle adjustment (2)

adjustable bracket

1.  Detection LED: relay 1 – opening field
2.  Detection LED: relay 2 – safety field
3.  Error LED
4.  Power LED

Remote control

sequence

Possible remote control

adjustments

Factory values

LED flashes slowly

All 4 LEDs can be switched off and on again by remote control.

This can be useful in cases where the sensor should not draw any attention.

Important

Tip

Quick

installation

75.5897.02 LZR-H110 20170821

Page 3 of 12

OBSOLETE

Summary of Contents for LZR-H110













Search results

Summary of Contents for LZR-H110

Reviews:

Related manuals for LZR-H110

Brands by name

Popular brands

BEA LZR-H110, User Manual

Search results

Summary of Contents for LZR-H110

Reviews:

Related manuals for LZR-H110

Brands by name

Popular brands