background image

 

 

11 

3) Speaker

8

Ω damp proof speaker 

 

 

5.Warning Information

 

 

a.

       

Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

 

b.

       

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly 

qualified persons in order to avoid a hazard.

 

c.

       

This appliance is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for their safety.

 

d.

       

Children should be supervised to ensure that they do not play with the appliance.

 

e.

       

Details concerning cleaning and other maintenance

 

f.

 

Maintenance of water purity, especially PH values and chlorine concentrations.

 

g.

       

Cleaning and disinfection

 

h.

       

Use and installation of a cover.

 

i.

 

Disposal of water

 

j.

 

Precautions to avoid damage due to water freezing

 

k.

       

Precautions to avoid damage when the appliance is left empty for extended period.

 

         

 

         

2.2 Sub-clause 7

 

          The installation instruction shall state the substance of the following:

 

-

   

Earthed appliances must be permanently connected to fixed wiring;

 

-

   

The appliance should be supplied through a residual current device (RCD) having a rated residual 

operating current not exceeding 30 mA.

 

-

   

The floor has to be capable of supporting the expected load.

 

-

   

An adequate drainage system has to be provided to deal with overflow water.

 

-

   

Details of how to follow the wiring rules, for example, specifying that parts are installed in the correct zone 

and that equipotential bonding is carried out.

 

 

WARNING

 

 

1

DANGER

RISK OF ELECTRIC SHOCK

Connect only to a circuit protected by a Ground 

Fault Circuit lnterrupter. 

2

Grounding is required. The unit should be installed by a qualified service representative and 

ground. 

3

FOR YOUR SAFETY-This product should be installed by a professional service   

      technician,qualified in hydrotherapy bath installation. 

4

lt

’s prohibited to cover the instrument with something while opeating. 

5

when using at the first time ,Be sure there is water in heater pipe before staring. 

6

parts containing live parts, except parts upplied with safety extra-low voltage not    Exceeding 

12V,must be inaccessible to person in the bath

 

8

earthed appliances must be permanently connected to fixed wiring

 

9

the  appliance  should  be  supplied  through  a  residual  current  device  (RCD)having  a  rated 

residual operating current not exceeding 30 mA. 

1

0、

If  the  mains  cord  of  this  appliance  is  damaged,It  must  only  bereplaced  by  our  service 

representative,As special tools and/or parts are required 

Summary of Contents for SPA-520

















Reviews: