background image

 

 

 
 
 

1

 

Press

 

“”

  and enter Pre-heating setting mode, and the LCD flashes of 

“ON” 

, the “PREHEAT” icon 

will flash

 , and then the circulation works on. Press

again to

 turn off pre-heating. The LCD will show 

OFF

  without flashing.   

2

 

Press

minutes

and

hours

  to adjust the time. 

It will add 1 minute when pressing

 

MIN

  each time and the minutes could be added continually. 

The adjustment range is 0~59. 

It will add 1 hour when pressing 

HOUR

  each time and the hours could be added continually. The 

adjustment range is 

0-23.

 

 

After setting the heating pre-set timing, proceed to the next step.

 

3)

Press

  to set the circulation times; it will show the minimum(10 minutes) on the LCD and this time 

will not flash. It will add 10 minutes by pressing 

  each time.

 It will add 1 hour by pressing

each  time

The  maximum  working  time  is  19hours  and  50  minutes.

  When  you  have  completed  this  procedure 

continue to the next setting. 

4)

Press

 

SET

VOL+

  again It will show 

  SET

  on the LCD panel. Press

 

  button to change the 

setting temperature. The range of temperature setting is: 

15~45

℃。

 

5)

When everything is set correctly, press the

 

  to confirm,

 the system will quit the pre-heating setting 

mode. 

***Notice*** 

1

All setting of preheating must be in Power OFF mode, just turn on the spa

the 

LCD will display 

---

 

 

2

Please note that it shows "on" or "off" on the LCD.    "on" means  preheating is 

turned on mode. when the time of pre-heating is as same as current time, the heater 
will start working. "off" means the heater won

’t start to work an any time.

 

 

3

Circulation PUMP and HEATER without working while setting preheating.

 

 

6

Operation of 

preheating

: 

When the preheating time is as same as the current time, the LCD screen shows 

“on” and the tub is also 

filled with water. The heater will start to work. The heater, circulation pump and time counting work at simultaneity. 
The countdown time will be shown on the LCD screen, till the preset time is finished. 

 

During the preheating, The preheating will be turned off automatically once the preset time is finished.   

Summary of Contents for SPA-520

















Reviews: