Beam Tech BS-1200 User Manual Download

Page: 9 / 10

8. SPECIFICATIONS:

BS-600

BS-1200

BS-1700 BS-2200

CAPACITY

600VA/360W 1200VA/700W 1700VA/1050W 2200VA/1400W

INPUT Voltage Frequency Selectable 100/110/115/120V 1ø or 200/220/230/240V 1ø

50Hz/60Hz Auto detect

Current (110V/220V)

6A / 3A

12A / 6A

16A / 8A

21A / 10A

Voltage

100/110/115/120V 1ø or 200/220/230/240V 1ø

6% for Back-up Mode

＜

10% for AVR

Frequency 50Hz or 60Hz ± 0.1Hz (Selectable under DC start)

OUTPUT

Wave Form Simulated Pseudo Sine Wave

Current (110V/220V)

5.5A / 2.8A

11A / 5.5A

15.5A / 7.8A

20A / 10A

TRANSFER TIME

4 ms typical.

BATTERY

Lead-Acid, maintenance free

Voltage/Capacity 12V 7Ah X 1pcs 12V 7Ah X 2pcs 12V 7Ah X 3pcs 12V 7Ah X 4pcs

Level

Ind.

YES YES YES YES

Recharge Time

90% within 8 hrs

90% within 5 hrs

LED/ALARM INDICATION

Normal/In charge GRN LED, No Beep.

Back up / Abnormal Input Voltage ORG LED Flashing, 2 Beeps / 8 sec.

Abnormal Input Frequency (Back up) ORG LED Rapid Flashing, No Beep.

Green mode auto off ORG LED flashing, 1 Beep / 4 sec. (Auto off after 24 sec.)

Low Battery ORG LED Flashing, 4 Beeps / sec.

Battery Replacement RED LED Flashing, 8 Beeps/ sec.

Over Load/Fault RED LED Flashing, Continuous Beep.

INDICATION OF SPECIAL STATUS

Replace Battery / Alarm Off / Charging / Buck / Boost

DC START / ALARM RESET

YES

BATTERY LOAD INDICATION

YES

ENVIRONMENT TEMP.

0 - 37

℃

ENVIRONMENT HUMIDITY

30-95% Non-Condensing

DIMENSIONS (L x H x W) (cm)

38 x 20 x 18

44 x 20 x 18

51 x 20 x 18

SHIPPING DIM. (L x H x W) (cm)

48 x 33 x 30

54 x 33 x 30

61 x 33 x 30

WEIGHT (N.W. / G.W.) (kgs)

9/10

15/16

21.50/22.50

25/26

Summary of Contents for BS-1200











Search results

Summary of Contents for BS-1200

Reviews:

Related manuals for BS-1200

Brands by name

Popular brands

Beam Tech BS-1200, User Manual

Search results

Summary of Contents for BS-1200

Reviews:

Related manuals for BS-1200

Brands by name

Popular brands