background image

11

• Do not abuse your Hover-1 Beast, doing so can damage your unit 

and cause failure to the operating system leading to injury. Physical 

abuse, including dropping your Hover-1 Beast, voids the 

manufacturer warranty.

• Do not operate in or near puddles of water, mud, sand, stones, gravel, 

debris or near rough and rugged terrain.

• The Hover-1 Beast can be used on paved surfaces that are flat and 

even. If you encounter uneven pavement, please lift your Hover-1 Beast 

over and past the obstruction.

• Do not ride in inclement weather: snow, rain, hail, sleek, on icy roads or 

in extreme heat or cold.

• Bend your knees when riding on bumpy or uneven pavement to 

absorb the shock and vibration and help you keep your balance. 

• If you are unsure if you can safely ride on a specific terrain, step off and 

carry your Hover-1 Beast. ALWAYS BE ON THE SIDE OF CAUTION.

• Do not attempt to ride over bumps or objects greater then ½ in, even 

when prepared and bending your knees.

• PAY ATTENTION - look at where you are riding and be conscious of the 

road conditions, people, places, property and objects around you.

• Do not operate the Hover-1 Beast in crowded areas.

• Operate your Hover-1 Beast with extreme caution when indoors, 

especially around people, property, and narrow spaces.

• Do not operate the Hover-1 Beast while talking, texting, or looking at 

your phone.

• Do not ride your Hover-1 Beast where it is not permitted.

• Do not ride your Hover-1 Beast near motor vehicles or on public roads.

• Do not travel up or down steep hills.

• The Hover-1 Beast is intended for use by a single individual, DO NOT 

attempt to operate the Hover-1 Beast with two or more people.

• Do not carry anything while riding the Hover-1 Beast.

• Individuals with lack of balance should not attempt to operate the 

Hover-1 Beast.

• Pregnant women should not operate the Hover-1 Beast.

Summary of Contents for Hover-1 HY-X10





























Reviews: