background image

        U

SER

 M

ANUAL

 

I. B

EFORE

 

USING

 

THE

 

UNIT

 

Thank you for choosing 

podoTRONIC OPUS III 

micromotor unit.  The unit is intended for use only 

by a qualified podiatrist and manicurist for podiatry and manicure treatments.   It is not to be 

used for purposes other than Podiatry and nail treatments.   All warranaes against damages to 

persons and property fail to exist in this case. 

 

1. 

Read the instrucaons thoroughly and keep them safe for future reference. 

2. 

Make sure the unit was not damaged in transit.   

3. 

Store the carton and packaging material for any necessary future repair work. For the 

transport the original packaging material offers the best protecaon. 

Do not operate the unit: 

 

- If the electric cable or plug are damaged 

 

- If the unit is damaged or has been dropped 

- Without a clean filter bag properly in place 

4. 

Before using the unit, please make sure that the voltage indicated on the unit corresponds 

to mains electricity (230V / 50 Hz or 115V / 60 Hz).   

5. 

Install the unit on a flat stable surface.  Please make sure that the exhaust outlet at the 

rear of the control box is not obstructed and that there is adequate room for exhaust and 

air circulaaon at the rear of the unit.  Set the unit in a clean dry area.  Avoid placing the 

unit near any heaang sources or steam cleaners. 

 

 

6. 

Please avoid an abrupt temperature change, due to condensaaon of the device.Wait unal 

it has assumed the temperature of its surroundings. The operaang temperature lies 

b15°C and +40°C. 

 

 

4

Summary of Contents for Podo Equipment podoTRONIC OPUS III
















Reviews:

Related manuals for Podo Equipment podoTRONIC OPUS III