9
Instructions for use
Position your child comfortably with his/her back against the shell (C4) and make sure that there are no toys or other
hard objects in the shell. Slide buckle tongue sections together and insert them in the buckle (C5).
Pull the shoulder belts tight (C6), pull the remaining slack out of the belt system by pulling the belts tight with the
adjuster belt (C7).
Note!
• The tighter the belts are around the child, the better the protection.
• Check that the textured side of the belt pads is on the shoulders of your child
• The belts should never be twisted.
• If you are unable to click the tongue sections in the buckle, unblock the buckle by pressing the red button and try
again.
• If you are not able to fasten the harness belt properly or pull it tight, contact your supplier immediately. Under no
circumstances use the product!
Adjusting the height of the shoulder belts (C-E)
The correct belt height of the shoulder belts is attained when the belt disappears into the shell slightly above the
shoulder of the child. Make sure that the shoulder belts fit properly over the shoulders of the child (C8).
Loosen the shoulder belts by pressing the release button and pulling the shoulder belts towards you as far as possible
(C1). Note! Do not pull the belt pads.
Place the Bébé Confort Priori Side Protection System (SPS+) in the sleeping position (A) and open the belt guard door
(D1). Remove the shoulder belts from the belt yoke (D2).
Pull the shoulder belts through the shell and the cover out of the belt pads, but make sure that the buckle remains
fixed to prevent the belts twisting (D3).
If you wish to alter the belts from or to the lowest position, place the Bébé Confort Priori Side Protection System (SPS+)
in the sleeping position (A).
If you wish to alter the belts from or to the middle or highest position, place the Bébé Confort Priori Side Protection
System (SPS+) in the sitting position (A).
Loosen the top part of the cover (D4) and thread the belt pads through the cover and the shell (D5).
From the front thread one belt pad through the correct slot in the cover and shell (D6).
Thread this belt pad via the back through the adjacent hole (D7).
Thread the shoulder belts through the adjusted belt pads, the cover and the shell (D8-D9).
Refit the shoulder belts to the belt yoke and check that the red stitching (x3) on the belt ends and the belt yoke are
facing the shell (D10) – if this is not the case your belts are twisted – then close the belt guard door (D1).
Fasten the cover all around, behind the pins (E4). Check that it works!
Maintenance, removing the cover and the belt pads (C-E)
• The seat may be cleaned with luke-warm water and a gentle soap. Do not use any abrasive detergents.
• The cover must be washed by hand at a maximum temperature of 30 °C. Do not use a dryer (see also washing
instructions).
• The buckle may be cleaned with warm water.
• It is advisable to buy an extra cover when you purchase the Bébé Confort Priori Side Protection System (SPS+) enabling
the Bébé Confort Priori Side Protection System (SPS+) to be used at all times also when the cover has to be cleaned (or
dried).
Loosen the belts and the belt pads, see fig. D1-D5 under the section “adjusting the height of the shoulder belts”.
Loosen the cover all around and also at the release button/positioning handle (E1).
Pull the belts, buckle tongue sections and buckle through the cover.
Then remove the cover by pulling it carefully behind the release mechanism (E2).
After washing attach the belt pads (D6-D9) and place the cover on the shell.
Thread the buckle and buckle sections back through the cover and fasten the cover at the release button/positioning
handle (E3). Secure the cover on pins (E4).
Close the buckle (C5) and thread the belts through the belt pads, the cover and the shell (D9).
Attach the shoulder belts to the belt yoke and make sure that the red stitching (x3) on the belt ends and the belt yoke
EN
