background image

Installation 

 

 

3 Installation 

3.1  Transport and Unpacking 

The specified storage conditions must be observed (see chapter 

Technical Data

). 

3.1.1 Transport 

Despite the robust design of the unit, the components are sensitive to strong vibrations and impacts. 
During transport, your Control Panel should therefore be protected from excessive mechanical stress. 
Therefore, please use the original packaging. 

Danger of damage to the unit 

 

Attention 

If the device is transported in cold weather or is exposed to extreme variations in 
temperature, make sure that moisture (condensation) does not form on or inside the 
device. 

 
Prior to operation, the unit must be allowed to slowly adjust to room temperature. Should condensation 
occur, a delay time of approximately 12 hours must be allowed before the unit is switched on. 

3.1.2 Unpacking 

Proceed as follows to unpack the unit: 

1. Remove 

packaging. 

2.  Do not discard the original packaging. Keep it for future relocation. 

3.  Check the delivery for completeness by comparing it with your order. 

4.  Please keep the associated paperwork. It contains important information for handling the unit. 

5.  Check the contents for visible shipping damage. 

If you notice any shipping damage or inconsistencies between the contents and your order, you should 
notify Beckhoff Service. 

12

 

CP6900-0001-0000/ CP6906-0001-0000 

Summary of Contents for CP6900-0001-0000



























Reviews: