background image

Technical data, mounting, wiring

PS1021-2405-0000

18

Version: 1.0

3.8

Lifetime expectancy and MTBF

The lifetime expectancy shown in the table indicates the minimum number of operating hours (service life)
and is determined by the lifetime expectancy of the built-in electrolytic capacitors. The lifetime expectancy is
stated in operating hours and is calculated according to the specifications of the capacitor manufacturer. The
manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years (131,400h). Any
number exceeding this value represents a calculated theoretical lifetime which can be used to compare
devices.

AC 100V

AC 120V

AC 230V

Lifetime
expectancy

181,000h

194,000h

219,000h At 24V, 2.5A and +40°C

511,000h

548,000h

621,000h At 24V, 2.5A and +25°C

66,000h

68,000h

83,000h At 24V, 5A and +40°C

188,000h

193,000h

234,000h At 24V, 5A and +25°C

MTBF stands for 

M

ean 

T

ime 

B

etween 

F

ailure, which is calculated from the statistical failure rate of the

components and indicates the reliability of a device. It is a statistical representation of the probability of
equipment failure and does not necessarily represent the service life of a product.

The MTBF number is a statistical representation of the probability of equipment failure. An MTBF number of
1,000,000h, for example, means that statistically, if there are 10,000 devices in use, one device will fail every
100 hours. However, it is not possible to say whether the failed device has been in operation for 50,000
hours or only 100 hours.

AC 100V

AC 120V

AC 230V

MTBF SN 29500,
IEC 61709

1,065,000 h 1,147,000 h 1,379,000h At 24V, 5A and +40°C

2,038,000h

2,166,000h 2,519,000h At 24V, 5A and +25°C

MTBF MIL HDBK
217F

681,000h

651,000 h

645,000 h At 24V, 5A and 40°C; Ground Benign GB40

872,000 h

842,000 h

839,000 h At 24V, 5A and 25°C; Ground Benign GB25

165,000 h

164,000 h

168,000 h At 24V, 5A and 40°C; Ground Fixed GF40

206,000 h

205,000 h

211,000 h At 24V, 5A and 25°C; Ground Fixed GF25

Summary of Contents for PS1021-2405-0000




































Reviews: