background image

MD3150/3060 

 

 

Copyright BEGLE GmbH, All rights reserved.  

Page 5 

Internet: www.bue.de 

 

Functional description  

 

 

Microprocessor-based and equipped with a large measured-value memory, the MD 3150 is 
optimal for:

 

 

• 

Automatic temperature monitoring 

Measured values can be logged and saved automatically in free programmable time 
intervals.  

 

• 

Verification of temperature control settings 

 

e.g., for heating or refrigeration systems, air conditioners, food chill systems, 
temperature-sensitive technical equipment, etc.  
Data can be read out, processed and logged in a PC. 

 

• 

Comparative measurement of two temperature values (MD3150) 

If two temperature sensors are connected, two temperature values can be compared with 
each other, e.g., room temperature and temperature in the feeding line from the heater. 

 

 

 

 

Temperature measurement:

 Press 

the 

ON/OFF 

key to switch on the device

 

 

Mode functions:

 Press 

the 

Mode

 key a the 

+/-

 keys as needed

 

 

Switching off:

 Press 

the 

ON/OFF

 key once more.

 

 

 

 

 

The following data is restored when the device is switched on: 

 

- Measured values of the series  
- Min - Max  mean value storage  
- State settings : 

           - Intermittent measurement (°C, °F) 

    - 

Time-controlled 

switch-off 

(on/off) 

    - 

Interface 

output 

(on/off)

 

       

 

 

Brief use guide  

 

Mode 0: 

 

 

 

Changes the channel 1 / 2 / 1+2 (only MD3150) 

 

 

 

 

Display °C or °F  

Mode 1: 

 

 

 

Interface output in mode 0  ON/OFF 

 

 

 

 

Starts/stops the output measured values in the memory  

Mode 2: 

 

 

 

Measuring time interval  

 

 

 

 

 

Measuring time interval  

 

Mode 3: 

 

 

 

Starts a measuring series 

 

 

 

 

Interrupts or ends a measuring series 

Mode 4: 

 

 

 

Calls measured values of the saved measuring series 

 

 

 

 

 

Calls measured values of the saved measuring series 

 

Mode 5: 

 

 

 

Displays min, mean, max  

 

 

 

 

Deletes min, mean, max  

Mode 6: 

 

 

 

Trigger threshold temperature  

 

 

 

 

 

Trigger threshold temperature 

 

Mode 7: 

 

 

 OFF/

--- 

---

  or  ON/OFF 

 

 

 

 

Trigger condition (‘trig‘) and switch-off function (‘AoFF’), resp. 

Mode 8: 

 

 

 

For manual measurement  

 

 

 

 

Resets the measured value memory to 0  

 

 

 

Summary of Contents for MD3060

















Reviews: