M-3520 Instruction Book
6–4
7.
When testing in
DIAGNOSTIC MODE
is
complete, press
EXIT
until the following
message appears:
PRESS EXIT TO
EXIT DIAGNOSTIC MODE
8.
Press
EXIT
again to exit
DIAGNOSTIC
MODE
. The relay will reset and normal
running mode will resume.
■
■
■
■
■
NOTE
: Pressing any button other than
EXIT
will
return the user to
DIAGNOSTIC MODE.
Output Test (Relay)
The first step in testing the operation of the function
outputs is to confirm the positions of the outputs in
the unoperated or
OFF
position. This can be
accomplished by connecting a DMM across the
appropriate contacts and confirming open or closed
contacts. The de-energized or
OFF
positions for
each output is listed in Table 6-2, Output Contacts
t
u
p
t
u
O
/
y
a
l
e
R
r
e
b
m
u
N
*
t
c
a
t
n
o
C
n
e
p
O
y
l
l
a
m
r
o
N
d
e
s
o
l
C
y
l
l
a
m
r
o
N
t
c
a
t
n
o
C
1
3
3
4
3
A
/
N
A
/
N
2
1
3
2
3
A
/
N
A
/
N
3
9
2
0
3
A
/
N
A
/
N
4
7
2
8
2
A
/
N
A
/
N
5
5
2
6
2
A
/
N
A
/
N
6
3
2
4
2
A
/
N
A
/
N
7
1
2
0
2
1
2
2
2
8
8
1
7
1
8
1
9
1
)
t
s
e
T
-
f
l
e
S
(
9
5
1
4
1
5
1
6
1
)
y
l
p
p
u
S
r
e
w
o
P
(
0
1
A
/
N
A
/
N
3
1
2
1
d
e
z
i
g
r
e
n
e
-
e
d
r
o
F
F
O
e
h
t
o
t
s
d
n
o
p
s
e
r
r
o
c
t
c
a
t
n
o
c
e
h
t
f
o
n
o
i
t
i
s
o
p
"
l
a
m
r
o
N
"
*
.
y
a
l
e
r
e
h
t
f
o
e
t
a
t
s
Table 6-2
Output Contacts
For units with optional HMI panel:
Enter Diagnostic Mode as previously outlined.
Following completion of testing, the output contacts,
can be turned
ON
in the following manner:
1.
Press
ENTER
. The following is displayed:
RELAY NUMBER
1
2.
Press
ENTER
. The following is displayed:
RELAY NUMBER 1
OFF on
3.
Use the right button to highlight
ON
in
uppercase letters, which signifies
selection. The following is displayed:
RELAY NUMBER 1
off ON
4.
Press
ENTER
.
Output Relay
#1
will
energize.
The following is displayed:
RELAY NUMBER
1
5.
Choose output numbers 2–8 by using the
up and down arrow buttons to turn all
relays or outputs to the energized or
ON
position. When each output is turned on,
the appropriate
OUTPUT
LED turns on
and stays on.
6.
Use the DMM to verify the position of the
output contacts in the “operate” or
ON
position. The readings should be the
opposite of the initial reading above. All
outputs should be returned to their initial
de-energized or
OFF
positions. The
OUTPUT
LED’s will extinguish when each
output is turned off.
7.
If Output Relay testing is complete, press
EXIT
to return to the
DIAGNOSTIC MODE
menu.
Input Test (Status)
The
INPUT TEST
menu enables the user to determine
the status of the individual status inputs.
For units with optional HMI panel:
Each input can be selected by its number using the
up and down buttons. The status of the input will then
be displayed.
T
U
P
N
I
R
E
B
M
U
N
N
R
U
T
E
R
L
A
N
I
M
R
E
T
T
U
P
N
I
R
E
B
M
U
N
)
b
2
5
(
1
1
1
0
1
2
1
1
9
3
1
1
8
4
1
1
7
5
1
1
6
6
1
1
5
Table 6-3
Input Contacts
Summary of Contents for M-3520
