background image

 

F&E  Equipment

 

Service manual  V1.0 Gelovit 200 

 

Autor : Fin/DW 

Stand 11.02.09 

 Seite 5 von 6 

 

4.7 Readout of the hours of operation (device) 

 

Switch on the device and wait until the device is ready to work. Press and hold the cycle 
button
. When  the  device  has  beeped  4  times,  release  the  button. The device  shows  you 
the operating hours now. The displayed value must be multiplied with 10. 

 

 
4.8

 

Readout of the hours of operation (motor)

 

 

Switch on the device and wait until the device is ready. 
Press and hold the timer button. When the device has beeped 4 times release the button. 
Device shows the operating hours of the motor now. The displayed value must be multiplied 
with 10. 

 

 

4.9 Calibrating the sensors 

 

Switch on the device and wait until the device is ready. Press and hold the T1&T2&T3 but-
tons.
 When the device has beeped 4 times, release the buttons. 
With + / - buttons it is possible to set a correction value of ±0.9 ° C for the sensors. Upon 
delivery, this value is 0. The device remains in the calibrating mode, please switch it off/on 
the device to turn back to the user mode. 
  

5. Known bugs 

 

Currently no 

 
 

 

 

 

6. Elimination of faults 

 

 
Fault  

 

 

 

Cause  

 

 

 

Remedy 

 
SOS sound 

 

 

display or cable to the display 

 

Call Customer  

 

 

 

 

defective 

 

 

 

 

Service Dept. 

  E01   

 

 

Gel sensor defective   

 

 

Sensor exchange, 

E02   

 

 

Lower temperature sensor defective  

PCB exchange 

E03   

 

 

Upper temperature sensor defective 

E04   

 

 

Rotary sensor defective 

 

 

Motor exchange, 

 

 

 

 

 

 

 

 

 

 

PCB exchange 

E05   

 

 

Clock defective 

 

 

 

PCB exchange 

E20 

 

24V supply failure 

 

 

 

Check fuses,   

 

 

  

 

 

 

            Check power  

                                                                                supply at PCB 

E30,31,32 

 

 

engine brake failure    

 

 

PCB exchange 

 
 

Summary of Contents for Gelovit 200







Reviews: