background image

THANK YOU FOR PURCHASING THIS PRODUCT

Congratulations on your purchase.  Behlen Country has been in the business of providing 

quality equipment to landowners for more than 75 years.  Our 3-Point Equipment will provide 

many years of service when maintained by the operator and used in accordance with the 

capabilities of the product.  For questions about this product, or for parts inquiries,please 

contact our Customer Service Center listed below.

This manual contains valuable information 
about your new Rotary Tiller. It has been 
prepared to give you helpful suggestions for 
safety, operation, adjustment and service.  

It is the owner’s and or operator’s 
responsibility to:
• Read and understand the information 
contained in this manual. The use of this 
equipment is susceptible to certain hazards 
that cannot be protected against by mechanical 
means or product design.  All operators of 

this equipment must read and understand 
this entire manual, paying particular attention 
to safety and operating instructions, prior to 
using.
• Operate, lubricate, assemble, and maintain 
the equipment in accordance with all 
instructions and safety procedures in this 
manual.
• Inspect the equipment prior to each use and 
replace or repair any parts that are worn or 
damaged. 

TO THE CUSTOMER

  ASSEMBLY, OPERATION, & MAINTENANCE INSTRUCTIONS

Rotary Tillers

Hardware Kit

80900190

It is the policy of Behlen Country to improve its products where it is possible and practical to do so. 
Behlen Country reserves the right to make changes or improvements in design and construction at 
any time, without incurring the obligation to make these changes on previously manufactured units.

PO Box 569
Columbus, NE 
68602-0569

Ph: 1-800-447-2751
Fax: (402) 563-7447
www.behlencountry.com

STATEMENT OF POLICY

CUSTOMER SERVICE CENTER

F-20976-5 

TECHNICAL INFORMATION 70167

 

Rev. 6-1-15   2-10-12

Summary of Contents for 80900190















Reviews: