background image

THANK YOU FOR PURCHASING THIS PRODUCT

Congratulations on your purchase.

Behlen Country has been in the business of providing quality

equipment to landowners for more than 70 years. Our 3-Point Equipment will provide many years of

service when maintained by the operator and used in accordance with the capabilities of the product.

For questions about this product, or for parts inquiries, please contact our Customer Service Center

listed below

.For questions about this product, or for parts inquiries, please contact our

Customer Service Center listed below.

Post Hole Digger

F-20801

TECHNICAL INFORMATION 70155

12-3-10

CUSTOMER SERVICE CENTER

PO Box 569
Columbus, NE
68602-0569

Ph:

1-800-447-2751
Fax: (402) 563-7447
www.behlencountry.com

STATEMENT OF POLICY

It is the policy of Behlen Country to improve its products where it is possible and practical to do so.
Behlen Country reserves the right to make changes or improvements in design and construction at
any time, without incurring the obligation to make these changes on previously manufactured units.

ASSEMBLY, OPERATION, & MAINTENANCE INSTRUCTIONS

Hardware Kit

80900085

Summary of Contents for Post Hole Digger















Reviews: