5.
While playing a pattern, you can:
Press HOLD/REST to hold the current step.
Press RESET/ACCENT to return to step 1.
Press SHIFT and any STEP, and you can edit the gate length,
rest, accent, ratchet, glide but not note. Press SHIFT and
the same STEP again to exit step edit. (If playback is
paused, the same operation can edit the note as well.
Press PAGE to view the pattern page from 1 to 4.
Press SHIFT and PAGE to return to automatic page turning.
Press SHIFT and ARP/SETEND and a STEP to change the
sequence end step.
PLAY/STOP to pause playback.
6.
Press PLAY/STOP.
7.
Note: To play in reverse, press SHIFT and PLAY/STOP.
SAVING A PATTERN
1.
Press and hold SHIFT + PLAY/STOP for 2 seconds until the
LOCATOR LED of the current pattern number begins to
flash green slowly.
2.
Press a STEP switch 1 to 8 to select the new desired
pattern number.
3.
Press P STEP switch 1 to 8 to select the desired
bank number.
4.
Press SHIFT + REC to save the pattern and exit the
save mode.
RECALLING A SAVED PATTERN
1.
Press and hold PATTERN. The LOCATION LED will show
the current pattern number. Use the <KYBD or STEP>
switches to move up and down through the patterns 1 to
8, or press a STEP switch 1 to 8. You can also do this while a
pattern is playing.
2.
Press and hold SHIFT and PATTERN. The LOCATION LED will
show the current bank number. Use the <KYBD or STEP>
switches to move up and down through the banks 1 to 8,
or press a STEP switch 1 to 8. You can also do this while a
pattern is playing.
3.
Press PLAY/STOP to play back the current pattern.
4.
During playback, the LOCATION LEDs will show the current
page of the pattern (1 to 4), and the STEP Switch LEDs will
show the steps moving.
LIVE PERFORMANCE
During playback, temporary adjustments can be made as follows.
(None of these are saved with the pattern.)
1.
To add Ratchet to all steps of the pattern, press SHIFT and
adjust the GLIDE control.
2.
To add SWING, press SHIFT and adjust the TEMPO control.
3.
To mute the pattern, press SHIFT + HOLD/REST.
4.
To add an accent to all steps, press SHIFT + RESET/ACCENT.
5.
Use the <KYBD and STP> switches to change the octave.
The LEDs will show the current Octave in red.
EDITING A PATTERN
1.
To edit a pattern in Keyboard mode, press REC. The STEP
switch LEDs will light.
2.
Press PAGE to select the pattern page from 1 to 4 to be
edited. The green LOCATION LEDs 1 to 4 will show the
current page and the PAGE button LED lit to indicate the
page is locked (press SHIFT and PAGE to unlock).
3.
Press SHIFT and the STEP switch you want to edit. You can
enter a new note, or a rest, and adjust any of the other
parameters such as ratchet, glide on/o
ff, and so on.
4.
Press SHIFT and the next STEP switch to be edited.
(The steps will not automatically advance to the next step
in line; you can choose which steps to edit next.)
5.
Press REC to exit the editing mode.
6.
Press PLAY/STOP to listen to the edited pattern.
7.
Remember to save the pattern using the “SAVING A
PATTERN” procedure above.
61
Quick Start Guide
Summary of Contents for CRAVE
