background image

18

EURODESK SX3242FX/SX2442FX User Manual

Main Outputs (¼")

Type 

¼" TRS jack, electronically balanced

Impedance 

approx. 240 Ω balanced,  

approx. 120 Ω unbalanced

Max. output level 

+28 dBu

Main Inserts

Type 

¼" TRS jack, unbalanced

Max. input level 

+22 dBu

Mono Output

Type ¼

"

 mono jack, unbalanced

Impedance 

approx. 120 Ω

Max. output level 

+22 dBu

Low pass 

variable, 30 Hz to 200 Hz, 18 dB/oct.

Phones/CTRL Room Output

Type ¼

"

 TRS jack, unbalanced

Max. output level 

+19 dBu / 150 Ω (+25 dBm)

CD/Tape Out

Type 

RCA connector

Impedance 

approx. 1 kΩ

Max. output level 

+22 dBu

DSP

Type 

Texas Instruments

Converter 

24-bit delta-sigma,  

 64/128-times  oversampling

Sampling rate 

46 kHz

Main Mix System Data

(Noise)

Main mix @ -∞, channel fader @ -∞  -100 dB / -102.5 dB A-weighted
Main mix @ 0 dB, channel fader @ -∞  -82 dB / -85 dB A-weighted
Main mix @ 0 dB, channel fader @ 0 dB  -72 dB / -75 dB A-weighted

Power Supply

Power consumption 

50 W

Fuse (100 - 240 V~, 50/60 Hz) 

T 2,0 A H 250 V

Mains connector 

Standard IEC receptacle

Physical/Weight

SX2442FX

Dimensions (H x W x D) 

3.9 x 26.9 x 16.1

"

  

100 x 682 x 410 mm

Weight (net) 

19 lbs / 8.6 kg

SX3242FX

Dimensions (H x W x D) 

3.9 x 35.3 x 16.1

"

  

100 x 896 x 410 mm

Weight (net) 

24.3 lbs / 11.0 kg

1

 Equivalent Input Noise

2

 Measuring conditions: 1 kHz rel. to 0 dBu; 20 Hz - 20 kHz; line input; main output; unity gain.

3

 20 Hz - 20 kHz; measured at main output. Channels 1 - 4 unity gain; EQ flat; all channels on main mix; 

channels 1/3 as far left as possible; channels 2/4 as far right as possible; reference = +6 dBu.

BEHRINGER is constantly striving to maintain the highest professional standards.  As a result of these efforts, 
modifications may be made from time to time to existing products without prior notice.  Specifications and 
appearance may differ from those listed or illustrated.

Summary of Contents for Eurodesk SX2442FX





















Reviews: