background image

Foreword

Beijer Electronics, MA00739

Manual CAB15

Foreword

This manual describes the installation and function of CAB15, the CANopen 
adapter.

Connection to CAB15 is supported by operator terminals with at least 64 kB of 
memory.

Besides this manual, the documentation of the driver is also available.

 

Beijer Electronics AB, MA00739, 2004-03

Please read the entire installation manual prior to installing and using this equipment. Only qualified 
personnel may install, operate or repair this equipment. Beijer Electronics AB is not responsible for 
modified, altered or renovated equipment. Because the equipment has a wide range of applications, users 
must acquire the appropriate knowledge to use the equipment properly in their specific applications. 
Persons responsible for the application and the equipment must themselves ensure that each application 
is in compliance with all relevant requirements, standards and legislation in respect to configuration and 
safety. Only parts and accessories manufactured according to specifications set by Beijer Electronics AB 
may be used.
BEIJER ELECTRONICS AB SHALL NOT BE LIABLE TO ANYONE FOR ANY DIRECT, 
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM 
THE INSTALLATION, USE OR REPAIR OF THIS EQUIPMENT, WHETHER ARISING IN 
TORT, CONTRACT, OR OTHERWISE. BUYER’S SOLE REMEDY SHALL BE THE REPAIR, 
REPLACEMENT, OR REFUND OF PURCHASE PRICE, AND THE CHOICE OF THE APPLI-
CABLE REMEDY SHALL BE AT THE SOLE DISCRETION OF BEIJER ELECTRONICS AB. 

Summary of Contents for CAB15

















Reviews: