A Beijer Group Company
JetCon 1701GP-U is an PoE injector. The JetCon 1701GP-U is an advanced and cost effective
high power PoE injector, which applies power to Ethernet RJ-45 for power devices (PDs).
JetCon1701GP-U are classified as power source equipment (PSE), providing up to 90 watts to
powered devices(PD). It could provide power for the powered deviced (PD) which compliant
IEEE 802.3af/at/bt (draft 2.0). The JetCon 1701GP-U adopts rugged metal case design to
operate in harsh environment (-40~75°C). It also IP-31 standard protection. JetCon 1701GP-U
recommend working voltage is DC 52V. (Input range: DC44~ 57 V).
Grounding JetCon 1701GP-U
There is one grounding screw on the bottom side of JetCon 1701GP-U . Connect the frame
grounding of JetCon 1701GP-U to the grounding surface to ensure safety and prevent noise
for communication interference.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+ and V- contact on the terminal block
connector.
2. Tighten the wire-clamp screws to prevent the power wires loosened.
Overview
JetCon 1701GP-U
Quick Installation Guide V1.0
Package List
JetCon 1701GP-U Industrial PoE Injector
Quick Installation Guide
Mount the unit
Din-Rail mount: Mount the din-rail clip on the rear of JetCon 1701GP-U on the DIN rail. For
information about the DIN Rail installation, please refer to user’s manual.
Installation
The product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0)
Korenix Customer Service
KoreCARE is Korenix Technology's global service center, where our professional staffs are
ready to solve your problems at any time Korenix global service center's e-mail is
KoreCARE@korenix.com.
For more information and documents download please visit our website:
http://www.korenix.com/page/doc/index.aspx
Connecting to Network
Connecting the Gigabit PoE port:
The port supports IEEE 802.3af/at/bt PoE standard and
The PoE port can offer 15W/30W/60W/90W power one end of an Ethernet cable into the
UTP port of JetCon 1701GP-U , while the other end is connected to the attached networking
device.
Wiring the Relay Output
The relay output contacts are in the middle of the terminal block connector as shown below.
By inserting the wires, relay output alarm will detect power fault, and form a short circuit. The
alarm relay output is “Normal Open”. For more information, please refer Manual chapter for
more detail.
Note: The relay contact only support 1A current, DC 24V. It does not recommend apply
higher voltage and current that over this specification.
5 Years Warranty
Each of Korenix’s product line is designed, produced, and tested with high industrial standard.
Korenix warrants that the Product(s) shall be free from defects in materials and workmanship
for a period of five (5) years from the date of delivery provided that the Product was properly
installed and used.
This warranty is voided if defects, malfunctions or failures of the warranted Product are caused
by damage resulting from force measure (such as floods, fire, etc.), other external forces such as
power disturbances, over spec power input, or incorrect cabling; or the warranted Product is
misused, abused, or operated, altered and repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
Support
