“精锐”压缩冷凝机组
“SLIM POWER”CONDENSING UNIT
百
尔
制
冷（无
锡）有
限
公
司
Beijer Ref (Wuxi) Co. Ltd
PN:
YAL0002-60
Issue:
D
Date: 01/01/20
Page: 18 of 26
EN:
18
5、设备推荐安装在走廊尽头、空旷区域、卫生间或其它对噪音不敏感区域；
1.
Equipment is prohibited to be installed in flammable, explosive, steam, hot air or fume waste gas;
2.
If install in the corrosive gas around, need to be customized;
3.
Whether it is indoor or “SLIM POWER” unit, the installation space must have enough air flow and
good ventilation conditions, to avoid air short cycle, and is strictly prohibited in the confined space;
4.
Installed away from the noise sensitive areas, and to take proper account of the shock absorption and
sound insulation measures, to avoid vibration and noise into the building;
5.
Recommended to install in the end of the corridor, open area, bathroom or any nose insensitive area
；
3.1.2
位置要求
Location requirements
：
1
、所选择的设备安装位置，其基座、地面、支撑物或地基必须足够牢固，并能支持设备的重量；
2
、建议采取必要的措施防止地面积水对机组的危害；
3
、设备安装时应在周围留有足够的空间，便于机组的通风及日常的维护保养或维修工作，具体参考尺寸请见
3.2
；
4
、对于多台设备安装在一起的情况，必须合理布置，避免相互之间的气流干扰形成短循环；
5
、为保证机组的安全及寿命，建议安装在阴凉遮阳的地方；
1.
The installation position, base, ground, or foundation must be strong enough to support the weight of
the equipment;
2.
Take the necessary measures to avoid the ponding damage to the unit;
3.
Space around unit should be enough, for easy ventilation and daily maintenance, for specific
dimension, please refer to 3.2;
4.
For a number of equipment installed in the case, must be reasonable layout, to avoid mutual
interference to air flow of unit;
5.
To ensure the safety and life of the unit, recommended to install in a shade place
；
3.1.3
配电要求
Distribution requirements
：
1
、设备尽量使用专用电源，避免和其它用电设备共用；
2
、客户应提供足够的配电容量；
1.
Special power supply is recommended, avoid to sharing with other electric equipment;
2.
Power distribution capacity should be enough
；
3.2
外形尺寸
Dimensions
3.2.1
外形尺寸表（表中单位：
mm
）
Dimensions
（
unit
：
mm
）
机组型号
Model
安装孔长
Mounting
Hole Length
安装孔宽
Mounting
Hole Width
LxWxH
BD020MZ2*D BDX020LZ2*D-AG
585
388
1032x425x845
BD030MZ2*D BDX030LZ2*D-AG
585
388
1032x425x845
BD040MZ2*D BDX040LZ2*D-AG
585
388
1032x425x845
BD050MZ2*D BDX050LZ2*D-AG
585
388
1032x425x1245
BD060MZ2*D BDX060LZ2*D-AG
585
388
1032x425x1245
BD075MZ2*D BDX075LZ2*D-AG
585
388
1032x425x1245
机组型号
Model
安
装
孔
长
Mounting
Hole Length
安
装
孔
宽
Mounting
Hole Width
L x W x H
BDN020LZ2*D-F
BDN020LZ2*D
585
388
1032x425x845
BDN030LZ2*D-F
BDN030LZ2*D
585
388
1032x425x845
