Beissbarth Start Line MS 201, Original Instructions Manual

Troubleshooting   |  Start Line MS 201  |  47

en

1 695 108 073

  2016-07-27

| 

Bosch Automotive Service Solutions srl

10.  Troubleshooting 

Faults affecting operation of the machine may occur in the course of normal working MS 201. The following table 
lists possible faults not requiring expert attention.

i

To take action as quickly as possible it is important to quote the details on the rating plate (label on back of 
MS 201) and the nature of the problem when calling.

!

Work on the electrical, hydraulic and pneumatic system must be performed only by appropriately qualified 
personnel.

i

Consult customer service if the problem persists.

Problem

Cause

Solution

Turntable cannot rotate

Short circuit

R

Check cable of motor,

R

Change the motor,

R

Check the plug,

R

Check the reversing switch/change reversing switch,

R

Check the moving parts of the reversing switch,

R

Adjust the belt/ change the belt.

The pedal can not back to its original 

position

The spring is damaged

Change the spring

Bead blade can not separate the tire 

edge

The cylinder sealing kits is worn  

R

Change the sealing kits;

R

Change the new cylinder.

Air leakage at the center of the 

cylinder

The cylinder sealing kits is worn  

R

Change the sealing kits;

R

Change the cylinder.

Worm case can not work or the noise 

is too much

The worm case assembly is 

damaged

Change the worm case.

The turntable can not fix the rim

The turntable cylinder is 

damaged

R

Change the turntable cylinder; 

R

Change the turntable cylinder sealing kit.

The torque is not enough when 

demount/ mount the tire

The tensile force of the belt is 

not enough and the bead can 

not be led into the groove of 

the rim.

R

Adjust the belt;

R

Change the motor capacitor;

R

Change the motor,

R

Use the tire pressing help to lead the tire into the 

groove of the rim while keep full lubrication on the 

bead.

When lock the mounting head, the 

distance between the mounting head 

and the rim should not be too far or 

too near

Lock plate releases for the bad 

adjustment

R

Adjust the lock plate bolt at the back end of the 

hexangular shaft;

R

Adjust the lock plate bolt at the back end of the 

horizontal arm.

The vertical movement of the hexagon 

shaft is not smooth

The lock plate does not work

R

Change the lock plate,

R

The screw in the lock plate is loose,

R

Adjust the lock plate for the hexagonal shaft.

The mounting head can not lock for 

the mounting head move too much in 

the process of demount/mount tire 

and the rim is easy to be damaged

Lock cylinder is damaged, there 

is wear at the sliding position 

of horizontal/ vertical arm and 

without air to flow in

R

Change the lock cylinder sealing part;

R

Change the lock cylinder;

R

Adjust the bolt at the lower part of the horizontal arm, 

making the clearance between the horizontal arm 

bushing and hexangular shaft narrower;

R

Adjust the bolt at the front end of the vertical arm, 

making the clearance between the horizontal arm 

bushing and quartet shaft narrower;

R

Adjust the lock plate.

The vertical arm can not swing out or 

too slow

Vertical arm control air route 

with problem

R

Change vertical arm cylinder sealing kits;

R

Change vertical arm cylinder;

R

Check whether there is a kink in the air hose;

R

Check whether there is air leakage at the vertical arm 

tilt back control pedal valve;

R

Change the pedal valve;

R

Adjust the air flow at the nozzle on the adjusting valve.

Mounting head cylinder air leakage/

hook has no force

The cylinder piston is damaged/ 

sealing kits is broken

R

Change the cylinder piston;

R

Change the sealing kits of the cylinder;

R

Change the cylinder.