is a
BEK
brand.
4.
The nebulizer can be connected to the compressor by using the air hose with connector.
5.
Plug the DC adapter (optional) into the wall outlet; plug the power cord of the adapter into the socket on the
side of the compressor.
6.
Press the power switch to turn on the device. Begin treatment according to your physician’s instructions.
7.
Inhale and exhale naturally. Be sure to stop when the medication is exhausted.
Cleaning and Maintenance
Symptom
Probable Cause
Solution
The device does not work
or the device is on but
nebulizes weakly.
The device is on but does not
nebulize.
The plug is improperly inserted into the
device.
Compressor switch is off.
Air hose is bent.
Turn the switch on.
Remove any bend or kink in the air hose.
The spray nozzle does not place in its
position.
Place the spray nozzle in its correct position.
No medicine is left.
The medicine container and cap does not
assemble well.
The texture of medicine may be thick.
Add the appropriate amount of medicine
prescribed by your physician to the medicine
container.
Re-assemble the medicine container and cap
and twist them well.
Slightly shake the medicine well and then
nebulization will be produced.
Re-plug again and make sure that the plug is
properly inserted into the device.
Troubleshooting
Specifications
Symbol Information
Note
After the treatment, perform the followings in order:
1. Turn off the device.
2. Dis-connect the air hose.
3. Unplug the adapter.
4. Remove other used accessories.
5. Proceed with the cleaning procedure as directed.
Instructions on Mouthpiece and Mask
Mouthpiece
1.
Attach the mouthpiece to the top of the cap.
2.
Close your lips around the mouthpiece and start treatment as recommended by your doctor.
Mask
1.
Insert the mask into the cap.
2.
Place the mask onto your face and start treatment as recommended by your doctor.
Before Cleaning
Make sure that the nebulizer is turned off before disassembly.
For Accessories
1.
After you have disconnected the air hose, remove the mouthpiece / mask, cap, spray nozzle and
medicine container.
2.
Discard any remaining medications.
3.
Wash mouthpiece / mask, cap, spray nozzle and medicine container with running water or soak in
warm water for 15 minutes.
4.
Gently wipe off excess water with a clean dry cloth and allow to air dry on a clean paper towel.
Clean the unit and accessories (adapter not included) as directed below:
ITEM
WHEN TO CLEAN (
●
)
Accessories
Compressor unit
●
for the first time
●
after each use
●
a period of no use
○
for the first time
●
after each use
●
a period of no use
For the Compressor Unit
1. Use alcohol cotton swabs to wipe the outer casing of the compressor.
2. Let it air dry on a clean paper towel.
• The above-named accessories can be regarded as consumable items; please replace with new
ones if they are dirty and obstructed. To prevent cross-contaminations, do not share the
accessories with others.
• Use only the aerosol nebulizer kit manufactured by Lifechek for appropriate assembly.
Do not use accessories which are not supplied or recommended
Other cables and accessories may negatively affect EMC performance.
Note
Storage
• Always handle your nebulizer with care.
• Disconnect the power plug from the wall outlet when not in use.
• Keep your nebulizer out of children’s reach.
• If you store your nebulizer, do not bend the air hose.
• If you store your nebulizer, try to keep it in the following environmental ranges:
a) Temperature: -25 °C to 70 °C (-13 °F to 158 °F),
b) Relative humidity: 10% to 95%
• If possible, stroe your nebulizer in a well-ventilated room.
Disposal
The used unit should be treated as contaminated that may carry a risk of infection during nebulization. Dispose of
the device, components, used batteries, and optional accessories according to your local regulations.
Model No.:
TD-7013
Dimension & Weight:
125 x 115 x 46 mm; 220 g
Power Source:
DC 12 V power adapter
•
Input:
100 to 240V, AC
•
Output:
12V, 1A, DC
IP Classification:
IP21
Mode of Operation:
30 mins on/ 30 mins off
Nebulization Rate:
0.35 ml/min
Medication Capacity:
6 ml
MMAD:
Approximately 5 microns
Power Consumption:
12 W
Compressor Pressure Range:
97~124kPa (14~18 Psi)
Operating Pressure Range:
35 to 55kPa (5 to 8 Psi)
Maximum Flow Rate:
4 LPM (l/min)
Aerosol output:
1.80 ± 0.02 (ml)*
Aerosol output rate:
0.21 ± 0.02 (ml/min)**
*: Continue the treatment until the medication cup is empty or the mist stops.
**: The treatment time for aerosl output rate is 1 min.
Operating conditions:
5°C to 40°C (40°F to 104°F), 15% to 93% relative humidity, 700 hPa to 1060 hPa
Storage conditions:
-25°C to 70°C (-13°F to 158°F), 10% to 95% relative humidity.
Manufacturer
Type BF Equipment
Serial number
Ingress protection rating
Humidity limitation
Symbol
Referent
Consult instructions for use
Temperature limitation
Caution, consult accompanying documents
Authorized representative in the
European Community
Symbol
IP21
CE mark
Referent
RoHS Compliance
DISPOSAL: Do not dispose this product as
unsorted municipal waste.
Collection of such waste separately for special
treatment is necessary.