background image

12

4.  INSTALLATION

4.1 Location

When installed in a panel enclosure complying with
the requirements for Ex n protection as shown in
section 3.2 of this manual, the BA377NE may be
located in a Zone 2 hazardous area providing that
the operating temperature is between –40°C and
+60°C and the installation complies with the Timer or
Clocks certification requirements.

Certified Ex e

panel enclosures are frequently used as Ex n panel
enclosures as they satisfy the same impact and
ingress protection requirements.  

The BA377NE Timer or Clock has a stainless steel
housings with a 7J front of panel impact resistance
incorporating a 10mm thick toughened glass window
which can withstand a 4J impact.

This, together

with a captive silicone gasket which seals the joint
between the instrument and the panel, enclosure
provides IP66 ingress protection.

The BA377NE

has IP20 rear protection which can be increased to
IP66 by an optional A495 rear cover sealing kit.  

Although the front of the BA377NE Timer or Clock
has IP66 protection, it should be shielded from
continuous direct sunlight and severe weather
conditions. 

Fig 7 shows the overall dimensions of the BA377NE
together with the recommended panel enclosure
cut-out dimensions and terminals.

4.2 Installation Procedure

a. Cut the aperture specified in Fig 7 in the panel

enclosure. Ensure that the edges of aperture are
de-burred. 

b. Inspect the Timer or Clock's captive gasket and

ensure that it is not damaged before inserting it
into the panel enclosure aperture.

c. If the enclosure panel is less than 1.0mm thick,

or is non-metallic, an optional BEKA stainless
steel support plate should be slid over the rear of
the indicator before the panel clamps are fitted to
evenly distribute the clamping force and prevent
the enclosure panel being distorted or creeping.

d. Slide a panel clamp into the two grooves at each

corner of the indicator housing with the M3 stud
protruding through the hole at the rear of the
clamp. Fit the stainless steel spring washer over
the stud and secure with the stainless steel wing
nut.

e. Evenly tighten the four clamps to secure the

instrument.

The

recommended

minimum

tightening torque for each wing nut is 22cNm
(1.95 lbf in).

f. Connect the panel enclosure wiring to the rear

terminal blocks.

To simplify installation, the

terminals are removable so that wiring can be
completed before the instrument is installed.
Wiring should be supported to prevent damage
resulting from vibration.

g. Finally, fit a silicone rubber push-on cap to the

end of each M3 threaded rod. 

Support panel wiring to prevent vibration damage

Note:

 Optional backlight is internally powered

    Fig 7  BA377NE dimensions and terminals

Summary of Contents for BA377NE
















































Reviews: