BEKA BA377NE, Manual

23

6.5.7

Lower display:   

di5P-2

The configuration of the lower display which has six
12mm high digits, depend upon whether the repeat
timer function

CYCLE5

, which can repeat the timing

period up to 99 times or continuously with a
configurable delay between periods, is enabled.
The configuration options are:

CYCLE5

 disabled

The lower display shows the set time

5ET t

or the lower display may be disabled.

CYCLE5

 enabled

The lower display shows the total number of
repeat cycles requested together with the
current

cycle

number.

During

the

configurable delay between cycles the
display times-down from the requested
delay time to zero. Each operation may be
briefly named at it's start or periodically
throughout the cycle.
The lower display may also be disabled if
not required.

To check or change the configuration of the lower
display select

di5P-2

from the configuration menu

and press

(

which will reveal the existing setting

which can be changed by pressing the

*

or

&

button followed by the

)

button to enter the

selection and return to the configuration menu.

If the

CYCLE5

function is not enabled the

following two options are available:

5td

Lower display shows the Timer's set
time

5Et t

, from which the BA377NE

will time-up or time-down depending
upon the direction of count selected in
the   

uP or dn

 function.

oFF

Lower display disabled.

If the

CYCLE5

function is enabled the following

three options are available:

5td

Lower display shows the number of
cycles requested together with the
current cycle number.

During the

configurable delay period the display
times-down from the requested delay to
zero. A brief notification of timer status
i.e.

CYCLE

or

dELAY

is shown at start of

each period.

02   -  11

Current

Number of cycles

cycle 

requested, not shown

number

when cycle is

 continuously repeated.

LabEL

Exactly the same as

5td

, but timer

status i.e.

CYCLE

or

dELAY

is shown

periodically.

oFF

Lower display disabled.

6.5.8

Starting & stopping the Timer:  

5tAr5toP

The Timer may be started and stopped by a sensor
input signal or by operation of the front panel

*

or

&

 push buttons.

To check or change the control of the Timer, select

5tAr5toP

from the configuration menu and press

(

which will reveal the existing setting which can be
changed by pressing the

*

or

&

button followed

by the

)

button to enter the selection and return to

the configuration menu.  Options available are:

Voltage inputs or control from front panel

Display

Start

Stop

ControL 1

Input high

Input low

ControL 2

Input low

Input high

LoCAL

&

 button

*

 button

Contact and open collector inputs

Display

Start

Stop

ControL 1

Open

Closed

ControL 2

Closed

Open

Proximity detector input

Display

Start

Stop

ControL 1

Low current

High current

ControL 2

High current

Low current

6.5.9

Units of display:  

unit5

Defines the format of all displayed times, except the
delay time of the optional control outputs which is
shown in seconds and the grand total which is
shown in hours and tenths of an hour.

To check or change the units of display, select

unit5

from the configuration menu and press

(

which

will reveal the existing setting. The required units
can be selected by pressing the

*

or

&

button

followed by the

)

button to enter the selection and

return to the configuration menu.

The options

available are shown below:

Display

12 : 00 : 00

Hours, minutes & seconds

12 : 00

Hours & minutes

*

30 : 00

Minutes & seconds

30

Seconds

*

Only available when time in seconds specified in

any Timer function is zero or divisible by 60.

The Timer's maximum elapsed time in any format is
equivalent to 99 hours, 59 minutes & 59 seconds.