background image

29

TO REMOVE A CI CARD

When removing the CI card, make sure you pull out the CAM complete with the 

card fitted.

This function enables you to watch the scrambled services (pay services) in some 

channels. If you remove the CI Module, you can only watch the available non 

scrambled digital programmes.

2-

 Press the 

Standby

 button on the remote to turn on the TV.

3-

 Press the 

INPUT

 button on the remote to display the Source List. Use the 

Up/

Down

 buttons to select 

DTV

, and press the 

OK

 button. 

4-

 If the CI card is inserted properly, the CI MODULE will briefly be displayed on 

screen, The contents are dependent on the CAM provider in you country.

9.8- How To Connect CI (Common Interface) Card
1-

 To wiew the scrambled (pay) services in digital TV mode.

TO INSERT A CI CARD

 

(NOTE: The card on its own cannot be used on this TV. A CAM (Conditional Access 

Module) must be purchased and the card inserted into the CAM. The CAM / card 

holder is then inserted into the CI slot on the TV.)

Insert the CAM /  holder card into the slot in the direction of the arrow until it is fully 

located.

Side or Rear view of TV

Summary of Contents for 32WLU550FHID






































Reviews: