background image

7 / 41EN

Refrigerator / User Manual

 Installation

Always have the repair procedures 

carried out by the Authorised Service 

Agent. Manufacturer shall not be held 

liable for damages that may arise from 

procedures carried out by unauthorised 

persons.

To make the product ready for use, make 

sure that the electricity installation 

is appropriate before calling the 

Authorised Service Agent. If not, call 

a qualified electrician to have any 

necessary arrangements carried out.

C

Preparation of the location and 

electrical installation at the 

place of installation is under 

customer's responsibility. 

B

Product must not be plugged in 

during installation. Otherwise, 

there is the risk of death or 

serious injury!

B

WARNING:

Manufacturer shall 

not be held liable for damages 

that may arise from procedures 

carried out by unauthorised 

persons.

A

WARNING:

 

Prior to 

installation, visually check if 

the product has any defects on 

it. If so, do not have it installed. 

Damaged products cause risks 

for your safety.

C

Make sure that the power 

cable is not pinched or crushed 

while pushing the product into 

its place after installation or 

cleaning procedures.

3.1. Appropriate 

installation location

A

WARNING:

 

If the door of the 

room where the product will be 

placed is too small for the product 

to pass, then the product's doors 

can be removed and the product 

turned aside to pass it through.

• Choose a place at where you would 

use the product comfortably.

• Install the product at least 30 cm away 

from heat sources such as hobs, ovens, 

heater cores and stoves. Product must 

not be subjected to direct sun light and 

kept in humid places after installation.

• Appropriate air ventilation must be 

provided around your product in order 

to achieve an efficient operation. If the 

product is to be placed in a recess in 

the wall, pay attention to leave at least 

5 cm distance with the ceiling and side 

walls.

• Do not place the product on the 

materials such as rugs or carpets.

• Place the product on an even floor 

surface to prevent jolts.

• Do not install the product in places 

where the temperature falls below 

-5°C.

C

If two coolers are to be installed 

side by side, there should be at 

least 4 cm distance between 

them.

Summary of Contents for ASGP342B












































Reviews: