background image

12/EN

Installation

Read “Safety Instructions” section first!

Installation procedures must always be 

performed by the manufacturer, authorised 

service agent or a qualified person 

specified by the importer. To make the 

product ready for use, make sure that 

the electricity, tap water supply and water 

drainage systems are appropriate before 

calling the authorised service agent. If 

they are not, call a qualified technician 

and plumber to have the necessary 

arrangements carried out.

Preparation of the location and 

electrical, tap water and waste water 

installations at the place of installation 

is under customer's responsibility.

Installation and electrical connections 

must be carried out by the authorised 

service agent. Manufacturer shall 

not be held responsible for damages 

arising from processes carried out by 

unauthorised persons.

Prior to installation, check if the product 

has any defects on it. If the product 

is damaged, do not have it installed. 

Damaged products cause risks for your 

safety.

 

Make sure that the water inlet and 

discharge hoses are not folded, 

pinched or crushed while pushing the 

product into its place after installation 

or cleaning procedures.

 

The front of the appliance may not be 

removed on free-standing or under-the-

counter models. The warranty will be 

void if this is done.

When placing the product, pay attention not 

to damage the floor, walls, piping, etc. Do 

not hold the product from its door or panel 

to move it.

Appropriate installation location

 In the area where this product is 

installed, there must not be a lockable, 

sliding or hinged door that will restrict 

full opening of the product’s door.

Make sure that you select a location 

that will allow you to load and unload 

the dishes in a fast and comfortable 

manner.

 

Place the product on a solid and flat 

floor that has sufficient load carrying 

capacity! The product must be installed 

on a flat surface in order for the door to 

be closed properly and securely.

 

Do not install the product at places 

where temperature may fall below 0ºC.

 

Place the product on a hard floor. Do 

not place it on a long pile rug or similar 

surfaces.

 Do not place the product on the power 

cable.

 

Make sure that you select a location 

that will allow you to load and unload 

the dishes in a fast and comfortable 

manner.

 

Install the product at a place close to 

the tap and the drain hole. Select the 

installation location by considering 

that it will not be changed after the 

connections are made.

Connecting water supply

 We recommend installing a filter at 

the water inlet in order to prevent the 

dirt (sand, clay, rust) in the mains or 

water installation of your home from 

damaging the machine or the dishes.

4-

Summary of Contents for BDFS16020W



















































Reviews: