background image

15/EN

Preparation

 Read “Safety Instructions” section first!

Tips for energy saving

Following information will help you use the 

product in an ecological and energy-efficient 

manner.

Wipe away any coarse food remnants on the 

dishes before putting them in the product. 

 Manual pre-rinsing of tableware items 

leads to increased water and energy 

consumption and is not recommended.

 Washing tableware in a household 

dishwasher usually consumes less energy 

and water in the use phase than hand 

dishwashing when the household dishwasher 

is used according to the manufacturer’s 

instructions.

Operate the product after filling it completely. 

When selecting a programme, consider 

the table of "Programme data and average 

consumption values" given on Quick Guide.

Do not put more detergent than suggested 

on the detergent package.

Water softening system

The product is equipped with a water 

softening system which reduces the 

hardness of incoming water. This system 

softens the supply water to a level that will 

allow washing the dishes with the required 

quality.

 The mains water hardness must be 

softened if it is over 7°dH.  Otherwise, 

hardness ions will accumulate on 

the dishes that are washed and may 

affect the washing, rinsing and drying 

performances of the machine.

Adjusting the water softening 

system

Washing performance will increase when 

water softening system is adjusted properly.

5-

 Read “Quick Guide - Adjusting Water 

Softening System” before this section!

The regeneration of the water softening 

system can be done in all programmes 

during drying step. When regeneration 

occurs, duration, energy and water 

consumption of the programme increase.

For regeneration process; frequency of 

regeneration cycle, maximum additional 

duration, water and energy consumption 

are given in table below depending on 

Eco 50°C programme water consumption, 

when the dishwasher is run under standard 

conditions with 14 dH water supply on its 

Eco 50°C programme:

Eco 50°C water  consumption (l)

Regeneration after  …. cycles

Additional duration (min)

Additional water  consumption (l)

Additional energy  consumption (kWh)

12,3-14,7

5

5

3,0

0,05

9,6-12,2

6

5

3,0

0,05

9,0-9,5

7

5

3,0

0,05

8,0-9,0

8

5

3,0

0,05

7,0-7,9

9

5

3,0

0,05

For the water consumption of your 

dishwasher on Eco 50°C programme, 

look at the Programme data and average 

consumption values table given on Quick 

Guide.

Summary of Contents for BDIN Series



















































Reviews: