background image

EN  

Installation and operating manual

BEKOMAT

®

 3/6 CO Ex, 3/6 E Ex 

3

Contents

1.  Safety information ...........................................................................................................................................4

1.1.  Pictograms and symbols ........................................................................................................................... 4

1.1.1.  In this document ............................................................................................................................. 4

1.1.2.  On the unit ...................................................................................................................................... 4

1.2.  Signal words according to ISO 3864 and ANSI Z.535 ............................................................................... 4
1.3.  General safety instructions ........................................................................................................................ 5
1.4.  Transport and storage ............................................................................................................................... 7
1.5.  Proper use ................................................................................................................................................. 8
1.6.  Warranty and liability ................................................................................................................................. 8

2.  Product information ........................................................................................................................................9

2.1.  Type plate .................................................................................................................................................. 9
2.2.  Product overview and description ............................................................................................................. 9
2.3.  Control and display elements .................................................................................................................. 10
2.4. Function ................................................................................................................................................... 11
2.5. Dimensions .............................................................................................................................................. 12

2.5.1. BEKOMAT

®

 3 CO/E Ex ................................................................................................................ 12

2.5.2. BEKOMAT

®

 6 CO/E Ex ................................................................................................................ 12

2.6.  Technical data ......................................................................................................................................... 13

2.6.1.  Identification of explosion-proof equipment according to ATEX and EPL

 .................................... 14

3. Installation......................................................................................................................................................14

3.1. Warning ................................................................................................................................................... 14
3.2.  Example of installation ............................................................................................................................ 15
3.3. Installation ............................................................................................................................................... 16

4.  Electrical installation.....................................................................................................................................18

4.1.  Installation instructions ............................................................................................................................ 18
4.2.  Wiring diagram ........................................................................................................................................ 19
4.3.  Electrical connections .............................................................................................................................. 20

4.4.  Potential equalisation

 .............................................................................................................................. 21

4.5.  NAMUR interface .................................................................................................................................... 21

5. Commissioning..............................................................................................................................................21
6. Operation........................................................................................................................................................22
7.  Maintenance and servicing...........................................................................................................................23

7.1.  Maintenance schedule ............................................................................................................................ 23
7.2.  Cleaning device ....................................................................................................................................... 23
7.3.  Spare parts .............................................................................................................................................. 24
7.4. Accessories ............................................................................................................................................. 24

8.  Troubleshooting and repair ..........................................................................................................................25
9. Decommissioning..........................................................................................................................................25
10.  Dismantling and disposal ...........................................................................................................................25
11.  Declaration of Conformity...........................................................................................................................26

Summary of Contents for BEKOMAT 3 CO Ex





























Reviews: