background image

EN / 34

• Loading door may be stuck because of

the pressure it is subjected to. >>> Grab
the handle and push and pull the loading
door to release and open it.

• If there is no power, loading door of the

product will not open. >>> To open the
loading door, open the pump filter cap
and pull down the emergency handle po-
sitioned at the rear side of the said cap.
See 

Loading Door Lock [

}

 29]

Washing takes longer than specified in
the user manual. (*)

• Water pressure is low. >>> Product waits

until taking in adequate amount of water
to prevent poor washing quality due to
the decreased amount of water. There-
fore, the washing time extends.

• Voltage is low. >>> Washing time is pro-

longed to avoid poor washing results
when the supply voltage is low.

• Input temperature of water is low. >>>

Required time to heat up the water ex-
tends in cold seasons. Also, washing
time can be lengthened to avoid poor
washing results.

• Number of rinses and/or amount of rins-

ing water have increased. >>> Product
increases the amount of rinsing water
when good rinsing is needed and adds
an extra rinsing step if necessary.

• Excessive foam has occurred and auto-

matic foam absorption system has been
activated due to too much detergent us-
age. >>> Use recommended amount of
detergent.

Programme duration does not count-
down. (On models with display) (*)

• Timer may stop during water intake. >>>

Timer indicator will not countdown until
the product takes in adequate amount of
water. The product will wait until there is
sufficient amount of water to avoid poor
washing results due to lack of water.
Timer indicator will resume countdown
after this.

• Timer may stop during heating step. >>>

Timer indicator will not countdown until
the product reaches the selected temper-
ature.

• Timer may stop during spinning step.

>>> Automatic unbalanced load detec-
tion system is activated due to the unbal-
anced distribution of the laundry in the
product.

Programme duration does not count-
down. (*)

• There is unbalanced load in the product.

>>> Automatic unbalanced load detec-
tion system is activated due to the unbal-
anced distribution of the laundry in the
product.

Product does not switch to spinning
step. (*)

• There is unbalanced load in the product.

>>> Automatic unbalanced load detec-
tion system is activated due to the unbal-
anced distribution of the laundry in the
product.

• The product will not spin if water is not

drained completely. >>> Check the filter
and the draining hose.

• Excessive foam has occurred and auto-

matic foam absorption system has been
activated due to too much detergent us-
age. >>> Use recommended amount of
detergent.

Washing performance is poor: Laundry
turns gray. (**)

• Insufficient amount of detergent has been

used over a long period of time. >>> Use
the recommended amount of detergent
appropriate for water hardness and the
laundry.

• Washing has been made at low temper-

atures for a long time. >>> Select the
proper temperature for the laundry to be
washed.

• Insufficient amount of detergent is used

with hard water. >>> Using insufficient
amount of detergent with hard water
causes the soil to stick on the cloth and
this turns the cloth into gray in time. It is
difficult to eliminate graying once it hap-
pens. Use the recommended amount of
detergent appropriate for water hardness
and the laundry.

Summary of Contents for CM 9101 BB









































Reviews: