background image

28

Dishwasher / User’s Manual

/38 EN

Operating the product

Starting the programme

To start your machine after selecting the 

programme and auxiliary functions, press 

Start/Pause/Cancel key.

C

Your machine performs water 

softening depending on the 

hardness level of the mains 

water. Due to water softening 

process the programme 

duration may change. The 

programme duration can also 

change while the programme 

is running depending on the 

ambient temperature where 

your machine is installed, 

temperature of the supply 

water and amount of the dishes.

C

Pay attention not to open the 

door of the machine when it is 

running. Stop the machine by 

pressing Start/Pause/Cancel 

key if you have to open the 

door. Then, open the door of 

the machine. There may be a 

rush of vapour when you open 

the door of your machine; be 

careful. Close the door of your 

machine and press Start/Pause/

Cancel key again. Programme 

will resume running.

C

After the rinsing step, the 

machine will wait silent in pause 

mode for some time in order 

to have the water remaining in 

the machine and on the dishes 

drained completely and to have 

the water softener cleaned, and 

then it will resume running in 

drying mode.

Programme follow-up

You can track the current step of the 

selected programme on the programme 

step lights located on the control panel.

C

If the drying light is on, the 

machine will perform silent 

drying for 30-60 minutes. At the 

end of this period, the Drying 

light will go off and the End light 

will become on.

The End light will become on when the 

selected washing programme ends.

Cancelling the programme

1.  Press and hold the Start / Pause / 

Cancel key for 3 seconds to cancel the 

programme.

2.  Release it when the Washing and 

Drying lights start flashing. Water in 

the machine will be discharged in 45 

seconds. The programme will have 

been cancelled once the Washing and 

Drying lights go off and the End light 

becomes on. Then, you can select and 

operate a new programme.

C

There might be residues of 

detergent or rinse aid left in the 

machine and/or on the pieces 

being washed depending on the 

step in which the programme 

has been cancelled.

C

When you set the Programme 

Selection Knob to “Off” position, 

the washing programme will 

end and the machine will be 

ready for a new programme 

selection. If you end the 

washing cycle this way, water 

and detergent may remain in 

the machine.

Summary of Contents for DFS05014X









































Reviews: