21
EN
Instruction for use
Electrical requirements
Before inserting the plug into the wall socket
make sure that the voltage and the frequency
shown in the rating plate inside the appliance
corresponds to your electricity supply.
The plug has to be accessible after installation
in order to allow disconnection of the appliance
from the supply after installation.
Warning! This appliance must be earthed.
Repairs to the electrical equipment may only be
made by qualified experts. If the power cable is
damaged, the manufacturer or customer service
must replace it in order to avoid danger.
ATTENTION!
This appliance operates with R600a which is an
environmental friendly but flammable gas.
During the transportation and fixing of the
product, care must be taken not to damage the
cooling system. If the cooling system is
damaged and there is a gas leakage from the
system, keep the product away from open flame
sources and ventilate the room for a while.
WARNING -
Do not use mechanical devices or
other means to accelerate the defrosting
process, others than those recommended by
the manufacturer.
WARNING -
Do not damage the refrigerant
circuit.
WARNING -
Do not use electrical appliances
inside the food storage compartments of the
appliance, unless they are of the type
recommended by the manufacturer.
WARNING -
If the supply cord is damaged, it
must be replaced by the manufacturer, its
service agent or similarly qualified persons in
order to avoid a hazard.
Transportation instructions
1. The appliance should be transported only in
an upright position. The packing as supplied
must be intact during transportation.
2. If during the transport the appliance, has
been positioned horizontally, it must not be
operated for at least 4 hours, to allow the
system to settle.
3. Failure to comply with the above instructions
could result in damage to the appliance, for
which the manufacturer will not be held liable.
4. The appliance must be protected against rain,
moisture and other atmospheric influences.
Important!
• Care must be taken while cleaning/carrying the
appliance not to touch the bottom of the
condenser metal wires at the back of the
appliance, as this could cause injury to fingers
and hands.
• Do not attempt to sit or stand on top of your
appliance as it is not designed for such use.
You could injure yourself or damage the
appliance.
• Make sure that the mains cable is not caught
under the appliance during and after moving, as
this could damage the cable.
• Do not allow children to play with the appliance
or tamper with the controls.
Installation instructions
1. Do not keep your appliance in a room where
the temperature is likely to fall below
-15 degrees C (5 degrees F) at night and/or
especially in winter, as it is designed to operate
in ambient temperatures between -15 and +43
degrees C (5 and 109 degrees F). At lower
temperatures the appliance may not operate,
resulting in a reduction in the storage life of the
food.
2. Do not place the appliance near cookers or
radiators or in direct sunlight, as this will cause
extra strain on the appliance's functions. If
installed next to a source of heat or freezer,
maintain the following minimum side
clearances:
From Cookers 30 mm
From Radiators 300 mm
From Freezers 25 mm
3. Make sure that sufficient room is provided
around the appliance to ensure free air
circulation
(Fig. 2).
• Put the back airing lid to the back of your
refrigerator to set the distance between the
refrigerator and the wall
(Fig. 3).
4. The appliance should be positioned on a
smooth surface. The two front feet can be
adjusted as required.To ensure that your
appliance is standing upright adjust the two front
feet by turning clockwise or anti-clockwise, until
firm contact is secured with the floor. Correct
adjustment of feet prevents excessive vibration
and noise
(Fig. 4).
5. Refer to "Cleaning and Care" section to
prepare your appliance for use.
Temperature control and adjustment
The freezer temperature is influenced by the
Freezer Set Function
(position 1, Fig. 5).
Generally, this temperature is bellow -18°C.
Lower temperatures can be obtained by
adjusting the Freezer Set Function towards
coldest position. We recommend checking the
temperature with a thermometer to ensure that
the storage compartments are kept to the
desired temperature. Remember to take the
reading immediately since the thermometer
