background image

7 / EN

Washing Machine / User’s Manual 

4.1 Installation

•  Apply to the nearest authorized service agent for the installation of your product. 

•  Preparation of the location and electrical, tap water and waste water installations at the place of 

installation is under customer's responsibility. 

•  Make sure that the water inlet and discharge hoses as well as the power cable are not folded, 

pinched or crushed while pushing the product into its place after installation or cleaning 

procedures. 

•  Make sure that the installation and electrical connections of the product are performed by 

authorized service. Manufacturer shall not be held liable for damages that may arise from 

procedures carried out by unauthorized persons. 

•  Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. 

Damaged products cause risks for your safety.

4.1.1 Appropriate installation location

•  Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other 

similar surfaces.

•  When the washing machine and drier are placed on top of each other, their total weight –when 

loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient 

load carrying capacity!

•  Do not place the product on the power cable.

•  Do not install the product in the environments where the temperature falls below 0 ºC.

•  Leave a minimum space of 1 cm between the machine and the furniture.

•   On a graduated floor, do not place the product next to the edge or on a platform.

4.1.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging 

reinforcement. Remove the packaging reinforcement by pulling the 

ribbon. Do not make this operation alone by yourself. 

4.1.3 Removing the transportation locks

1  Loose all bolts with an appropriate wrench until they turn freely

 (C)

.

2  Remove the transport safety bolts by turning them slightly.

3  Insert the plastic covers in the bag containing the user manual to the openings on the rear 

panel. 

(P)

A

CAUTION: 

Remove the transportation safety bolts before operating the washing machine! Otherwise, the 

product will be damaged.

C

Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again 

in the future.
Install the transport safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!

Summary of Contents for WMY 814831




























Reviews: