background image

23 / EN

Washing Machine / User’s Manual

Changing the auxiliary function, speed and 

temperature

Depending on the step the programme has 

reached, you can cancel or select auxiliary 

functions. See “Auxiliary function selection”. 
You can also change the speed and 

temperature settings. See "Spin speed 

selection" and "Temperature selection".

C

INFORMATION

•  If no change is allowed, the relevant light 

will flash 3 times.

Adding and removing laundry

1.  Press the “Start/Pause” button to pause the 

machine. The programme follow-up light of 

the relevant step during which the machine 

was switched into the pause mode will flash.

2.  Wait until the Loading Door can be opened.
3. Open the loading door and add or take out 

laundry.

4.  Close the loading door.
5. Make changes in auxiliary functions, 

temperature and speed settings if necessary. 

6. Press the “Start/Pause” button to start the 

machine. 

4.3.16 Cancelling the programme

To cancel the programme, turn the Programme 

Selection knob to select another programme. 

Previous programme will be cancelled. End/

Cancel light will flash continuously to notify that 

the programme has been canceled. 
When you turn the Programme Selection knob, 

the machine will end the programme but will not 

discharge the water inside. When you select 

and start a new programme, the newly selected 

programme will start depending on the step 

the previous programme was canceled in. For 

example, the machine may take in additional 

water or continue to wash with the water inside.

C

INFORMATION

•  Depending on the step where the 

programme was canceled in, you may 

have to add detergent and softener again 

for the programme you have selected 

anew.

4.3.17 End of programme

At the end of the programme, “End” will be 

displayed. 
1.  Wait until the light of the loading door goes 

off completely.

2.  Switch the programme selection knob to 

On/Off to switch off the machine.

3.  Take out your laundry and close the loading 

door. Your machine is now ready for the 

next washing cycle.

4.3.18 Your machine has the 

"Pause Mode" function.

After using the On/Off button to switch on the 

machine, if you do not start any programme in 

the selection step or do not perform anything 

else, or if you do not do anything in 10 minutes 

after the selected programme has ended, the 

machine will automatically switch to energy 

saving mode. Also, if your product has a display 

that shows programme time, this display will 

completely turn off. If you turn the Programme 

Selection knob or touch any button, the lights 

and the display will switch back to the previous 

position. The selections you make when exiting 

the energy efficiency mode may change. Check 

if your selections are correct before starting the 

programme. If necessary, make adjustments 

again. This is not an error.

Summary of Contents for WTL94121

































Reviews: