Beko WTXS61032W/IT, User Manual

47 / EN

Washing Machine / User Manual

3  Follow the below procedures in order to 

drain water.

The product has an emergency water draining 

hose, in order to drain the water:

a  Pull the emergency draining hose out from 

its seat

b  Place a large container at the end of the 

hose. Drain the water into the container by 

pulling out the plug at the end of the hose. 

When the container is full, block the inlet 

of the hose by replacing the plug. After 

the container is emptied, repeat the above 

procedure to drain the water in the machine 

completely.

c  When draining of water is finished, close the 

end by the plug again and fix the hose in its 

place.

d  Turn and remove the pump filter.
4.  Clean any residues inside the filter as well 

as fibres, if any, around the pump impeller 

region.

5.  Replace the filter.
6.  If the filter cap is composed of two pieces, 

close the filter cap by pressing on the tab. 

If it is one piece, seat the tabs in the lower 

part into their places first, and then press 

the upper part to close.

5 Troubleshooting

Program does not start after closing the door.

• Start / Pause / Cancel button was not pressed. >>>*Press 

the Start / Pause / Cancel button.

• It may be difficult to close the loading door in case of 

excessive loading. >>>Reduce the amount of laundry and 

make sure that the loading door is closed properly.

Programme cannot be started or selected.

• Washing machine has switched to self protection mode 

due to a supply problem (line voltage, water pressure, 

etc.). >>>To cancel the programme, turn the Programme 

Selection knob to select another programme. Previous 

programme will be canceled. (see. “Cancellation of 

program”)

Water in the machine.

• Some water might have remained in the product due to the 

quality control processes in the production. >>>This is not 

a failure; water is not harmful to the machine.

The machine enters standby mode after the 

programme starts or it does not take in water.

• Tap is turned off. >>>Turn on the taps.

• Water inlet hose is bent. >>>Flatten the hose.

• Water inlet filter is clogged. >>>Clean the filter.

• Loading door may be open. >>>Close the door.

• The water connection may be wrong or water may be cut 

off (When the water is cut off, washing or rinsing LEDs 

flash). >>>Check the water connection. If the water is cut 

off, press the Start/Pause key after the water has been 

supplied again to resume the operation from standby 

mode.

Machine does not drain water.

• Water drain hose might be clogged or twisted. >>>Clean 

or flatten the hose.

• Pump filter is clogged. >>> Clean the pump filter.

Machine vibrates or makes noise.

• Machine might be standing unbalanced. >>>Adjust the 

feet to level the machine.

• A hard substance might have entered into the pump filter. 

>>>Clean the pump filter.

• Transportation safety bolts are not removed. >>>Remove 

the transportation safety bolts.

• Laundry quantity in the machine might be too little. >>>Add 

more laundry to the machine.

• Machine might be overloaded with laundry. >>>Take out 

some of the laundry from the machine or distribute the 

load by hand to balance it homogenously in the machine.

• Machine might be leaning on a rigid item. >>>Make sure 

that the machine is not leaning on anything.

There is water leaking from the bottom of the 

washing machine.

• Water drain hose might be clogged or twisted. >>>Clean 

or flatten the hose.

• Pump filter is clogged. >>>Clean the pump filter.

Machine stopped shortly after the programme 

started.

• Machine might have stopped temporarily due to low voltage. 

>>>It will resume running when the voltage restores to 

the normal level.