Beko WTXS61032W/IT, User Manual

48 / EN

Washing Machine / User Manual

Machine directly discharges the water it takes in.

• Draining hose might not be at adequate height. 

>>>Connect the water draining hose as described in the 

operation manual.

No water can be seen in the machine during 

washing.

• The water level is not visible from outside of the washing 

machine. >>>This is not a failure.

Loading door cannot be opened.

• Door lock is activated because of the water level in the 

machine. >>>Drain the water by running the Pump or 

Spin programme.

• Machine is heating up the water or it is at the spinning 

cycle. >>>Wait until the programme completes.

• Child lock is engaged. Door lock will be deactivated a 

couple of minutes after the programme has come to an 

end.  >>>Wait for a couple of minutes for deactivation of 

the door lock.

• Loading door may be stuck because of the pressure it is 

subjected to. >>>Grab the handle and push and pull the 

loading door to release and open it.

Washing takes longer time than specified in the 

manual.(*)

• Water pressure is low. >>>Machine waits until taking in 

adequate amount of water to prevent poor washing quality 

due to the decreased amount of water. Therefore, the 

washing time extends.

• Voltage might be low. >>>Washing time is prolonged to 

avoid poor washing results when the supply voltage is low.

• Input temperature of water might be low. >>>Required 

time to heat up the water extends in cold seasons. Also, 

washing time can be lengthened to avoid poor washing 

results.

• Number of rinses and/or amount of rinse water might have 

increased. >>>Machine increases the amount of rinse 

water when good rinsing is needed and adds an extra 

rinsing step if necessary. 

• Excessive foam might have occurred and automatic foam 

absorption system might have been activated due to too 

much detergent usage. >>>Use recommended amount 

of detergent.

Programme time does not countdown. (On models 

with display) (*)

• Timer may stop during water intake.  >>>Timer indicator 

will not countdown until the machine takes in adequate 

amount of water. The machine will wait until there is 

sufficient amount of water to avoid poor washing results 

due to lack of water. Timer indicator will resume countdown 

after this.

• Timer may stop during heating step.  >>>Timer indicator 

will not countdown until the machine reaches the selected 

temperature.

• Timer may stop during spinning step.  >>>Automatic 

unbalanced load detection system might be activated due 

to the unbalanced distribution of the laundry in the drum.

Programme time does not countdown. (*)

• There might be unbalanced load in the machine. 

>>>Automatic unbalanced load detection system might 

be activated due to the unbalanced distribution of the 

laundry in the drum.

Machine does not switch to spinning step. (*)

• There might be unbalanced load in the machine. 

>>>Automatic unbalanced load detection system might 

be activated due to the unbalanced distribution of the 

laundry in the drum.

• The machine will not spin if water is not drained completely. 

>>>Check the filter and the draining hose.

• Excessive foam might have occurred and automatic foam 

absorption system might have been activated due to too 

much detergent usage.>>>Use recommended amount of 

detergent.

Washing performance is poor: Laundry turns gray. 

(**)

• Insufficient amount of detergent has been used over a long 

period of time. >>>Use the recommended amount of 

detergent appropriate for water hardness and the laundry.

• Washing was made at low temperatures for a long time.  

>>>Select the proper temperature for the laundry to be 

washed.

• Insufficient amount of detergent is used with hard water. 

>>>Using insufficient amount of detergent with hard 

water causes the soil to stick on the cloth and this turns 

the cloth into gray in time. It is difficult to eliminate graying 

once it happens. Use the recommended amount of 

detergent appropriate for water hardness and the laundry.

• Too much detergent is used. >>>Use the recommended 

amount of detergent appropriate for water hardness and 

the laundry.

Washing performance is poor: Stains persist or the 

laundry is not whitened. (**)

• Insufficient amount of detergent is used. >>>Use the 

recommended amount of detergent appropriate for water 

hardness and the laundry.

• Excessive laundry was loaded in. >>>Do not load the 

machine in excess. Load with amounts recommended in 

the "Programme and consumption table".

• Wrong programme and temperature were selected. 

>>>Select the proper programme and temperature for 

the laundry to be washed.

• Wrong type of detergent is used. >>>Use original detergent 

appropriate for the machine.

• Too much detergent is used. >>>Put the detergent in the 

correct compartment. Do not mix the bleaching agent and 

the detergent with each other.

Washing performance is poor: Oily stains appeared 

on the laundry. (**)

• Regular drum cleaning is not applied. >>>Clean the drum 

regularly. For this, please see 4.4.2.

Washing performance is poor: Clothes smell 

unpleasantly. (**)

• Odours and bacteria layers are formed on the drum as a 

result of continuous washing at lower temperatures and/

or in short programmes. >>>Leave the detergent drawer 

as well as the loading door of the machine ajar after each 

washing. Thus, a humid environment favorable for bacteria 

cannot occur in the machine.