Belair BCIF680B Manual Download

Page: 8 / 9

Cleaning and Maintenance

You can easily clean the surface of the induction hotplate by following the methods given in the table

below.

Type of contamination

Method of cleaning

Articles used for cleaning

Light

Wet with hot water then

wipe dry

Cleaning sponge

Accumulation of dirt

Wet with hot water then

wipe it dry with coarse

sponge

Special cleaning sponge for

ceramic glass

Rings and lime crumbles

Apply white vinegar to the

soiled zone, then wipe dry

with soft cloth

Special descaler for ceramic

glass

Burnt

food

,melted

aluminum or plastics

Use a scraper suitable for

ceramic glass (to protect

glass, a silicon product is

preferred)

remove

residue

Special cleaner for ceramic

glass

Always disconnect power before cleaning.

Failure Display and Inspection

If an abnormality occurs, the induction hob will enter the protective state automatically and display

corresponding protective codes:

Problem

Possible reasons

Solutions

Fan failure

Bad hob ventilation

Abnormal temperature

Please restart after the

hotplate cools down.

Please inspect the pan.

Please contact the

supplier.

Temperature sensor

failure

Please contact the

supplier.

Abnormal supply

voltage

Please inspect whether

power supply is normal.

Power on after the power

supply is normal.

Verify if the power supply

interface is secure. After

Summary of Contents for BCIF680B










Search results

Summary of Contents for BCIF680B

Reviews:

Related manuals for BCIF680B

Brands by name

Popular brands

Belair BCIF680B, Manual

Search results

Summary of Contents for BCIF680B

Reviews:

Related manuals for BCIF680B

Brands by name

Popular brands