Belarus 1221.2 Operator'S Manual Download

Page: 92 / 295

BELARUS-1221.2/1221

.2/1221.3 Description and operation

The

speed-gear assembly

is mounted

on the cover (54) and consists of the pri-

mary shaft (51) with driving pinions (2, 4,

6, 10) mounted in needle bearings riding

thereon. These pinions ensure engage-

ment of the 5

, 6

, 3

and 4

gear, re-

spectively. The driving pinion of the 1

gear is made integral with the shaft (51)

and the driving pinion of the 2

gear is

fixed rigidly on the shaft. The needle

bearings are force-lubricated through the

oil pipeline (53) and holes drilled in the

shaft. The male splines of the shaft carry

two inertia-type synchronizers (4) and (9);

the latter effect engagement of the 5

, 6

, and 4

gears. The primary shaft rests

on ball bearings mounted in the cover

(54) and casing (1).
The intermediate shaft (48) carries the

press-fitted driven pinions (54, 40 and 39)

of the 5

, 6

, 3

and 4

gear, respec-

tively. The driven pinions (43 and 41) of

and 1

gears, respectively, rest on

needle bearings. An inertia-type synchro-

nizer (42) to help engagement of the 1

and 2

gears.

The downshift and reverse gear shaft 3

(see Fig. E-15.2)

is mounted in the body

(4) and rests on bearings (1 and 12). The

shaft also carries a driven pinion (10)

which is coupled to the shaft through

bushings (9), forward driving pinion (8)

and reverse pinion (5) running in needle

bearings. These pinions are coupled with

the shaft through a toothed coupling (6).

Bushing (16) which sits on male splines

of the shaft is locked on the shaft by

means of a retaining ring (7).

Fig. E-15.2 Downshift and reverse gear shaft:

1, 12 – bearings; 2, 13 – nuts; 4 –casing; 5, 8, 10 –pinions; 6 – toothed coupling; 7 – retaining ring; 9 – bush-

ing; 11 – cover; 14 – oil delivery cup; 15 – oil pipeline; 16 – bushing

Summary of Contents for 1221.2








































































































































































































































































































Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands

Belarus 1221.2, Operator'S Manual

Search results

Summary of Contents for 1221.2

Reviews:

Related manuals for 1221.2

Brands by name

Popular brands