2122.6-0000010 OM
110
The fan shall rotate with the set revolutions until it is switched off (by the repeated
deflection of joystick 1 backwards and pressing the button from above).
Programme No.2 provides automatic execution of the following operations:
-
marker retraction;
-
seeding machine uplift from the operating position.
To record programme No.2 it is required to do as follows:
-
switch on OPU for HLL (in case it is off) by pressing button 1 (figure 3.2.7);
ATTENTION: BEFORE CARRYING OUT THE PROCESS OF PROGRAMME NO.2
RECORDING, IT IS REQUIRED TO SET THE SEEDING MACHINE IN THE MODE OF
MANUAL CONTROL TO THE REQUIRED POSITION (THE HYDRAULIC FAN DRIVE
MOTOR IS SWITCHED ON, THE MARKERS ARE EXPANDED, THE SEEDING MA-
CHINE IS LOWERED TO THE OPERATING POSITION).
-
press button 3 (figure 3.2.7) and hold it in a pressed position until an audible
signal gets activated (about two seconds) and annunciator 6 starts blinking;
-
press selection buttons 13, 14 for distributive valve EHS sections No.3 and
No.2 correspondingly. Annunciators for uplift and lowering 10 of these sections shall start
blinking;
-
uplift the marker using joystick 1 (figure 3.2.6), controlling on section No.2;
-
uplift the seeding machine using joystick 2, controlling on section No.3;
-
repeatedly press selection buttons 13, 14 (figure 3.2.7) for distributive valve
EHS sections No.3 and No.2 (recording on sections is finished);
-
to finish programming, press button 3 of the recordable programme No.2.
Programme No.3 provides automatic execution of the following operations:
-
lowering of the seeding machine and setting of the floating position;
-
marker expansion.
To record programme No.3 it is required to do as follows:
-
switch on OPU for HLL (in case it is off) by pressing button 1 (figure 3.2.7);
ATTENTION: BEFORE CARRYING OUT THE PROCESS OF PROGRAMME NO.3
RECORDING, IT IS REQUIRED TO SET THE SEEDING MACHINE IN THE MODE OF
MANUAL CONTROL TO THE REQUIRED POSITION (THE HYDRAULIC FAN DRIVE
MOTOR IS SWITCHED ON, THE MARKERS ARE RETRACTED, THE SEEDING MA-
CHINE IS IN A CONSTANTLY UPLIFTED POSITION).
-
press button 2 (figure 3.2.7) and hold it in a pressed position until an audible
signal gets activated (about two seconds) and annunciator 7 starts blinking;
-
press selection buttons 13, 14 for distributive valve EHS sections No.3 and
No.2 correspondingly. Annunciators for uplift and lowering 10 of these sections shall start
blinking;
-
set “floating” position using joystick 2 (figure 3.2.6), controlling on section
No.3, by doing so annunciator 9 (figure 3.2.7) displays FL;
-
expand the marker using joystick 1 (figure 3.2.6), controlling on section No.2;
-
repeatedly press selection buttons 13, 14 (figure 3.2.7) for distributive valve
EHS sections No.3 and No.2 (recording on sections is finished);
-
to finish programming, press button 2.
ATTENTION:
BEFORE EXECUTION OF PROGRAMME NO.2, MAKE SURE THAT THE SEED-
ING MACHINE IS IN THE CORRESPONDING POSITION - THE HYDRAULIC FAN
DRIVE MOTOR IS SWITCHED ON, THE MARKERS ARE EXPANDED, THE SEEDING
MACHINE IS LOWERED INTO THE OPERATING POSITION!
BEFORE EXECUTION OF PROGRAMME NO.3, MAKE SURE THAT THE SEED-
ING MACHINE IS IN THE CORRESPONDING POSITION – THE HYDRAULIC FAN
DRIVE MOTOR IS SWITCHED ON, THE MARKERS ARE RETRACTED, THE SEEDING
MACHINE IS IN THE UPLIFTED POSITION!
https://tractormanualz.com/