manualshive.com logo in svg

Belarus 3522.5, Operator'S Manual

Looking for the Belarus 3522.5 Operator's Manual? Look no further! Our website offers a free download of this essential manual, providing detailed instructions and guidance for operating your Belarus 3522.5. Visit 88.208.23.73:8080 to access this manual and maximize your product's potential.

Share
Download
background image

3522.5-0000010 OM

328

7.4 Possible failures in the electrical equipment and guidelines for trouble-

shooting

7.4.1 General information

The

structure of an electrical equipment of the tractor «BELARUS-3522.5» includes

electric elements (switches, relays, electric motors, instruments, flashlights, headlights,
fuses, break-in relays, sensors and etc.) and also wiring system and the electrical connec-
tors for coupling of an element with power supply and with body ground. For facilitation of
the task fulfillment and of search for failures in the electrical equipment the electric circuit
diagram is enclosed to the present operation manual (Annex D).

Before starting the troubleshooting procedure for any loop, take a good look at the

electric circuit diagram to clearly realize the functional purpose of the loop. A search may
be narrowed by gradual identification and exclusion of the proper operating components of
the single loop. In case several electrical elements are disabled, blow out of the respective
fuse or null “ground” (in many cases distinct electrical elements may be closed on a single
fuse or on the unified “ground” terminal) is the most probable cause of failure.

Electrical equipment failure can often be explained by the simplest reasons like

terminal corrosion, fuse breakdown, fusible element burn-out or transfer relay defect. Carry
out the visual inspection of all the fuses, wires and loop electrical connector before starting
more certain fault checking of its components.

If the diagnostic instruments are used for failures search, use the electric circuit dia-

gram enclosed to decide carefully on which points of the loop the instrument shall be con-
nected to in order to improve the localization of failures. Among the main diagnostic in-
struments there are electric circuits testing apparatus (multimeter), voltmeter (12 V-test
lamp (about 21 W) with connecting wires set can also be used), loop interval conductivity
indicator (tester) with the lamp, own power supply unit and connecting wires set.

Electrical circuits failure diagnostics is not a difficult task in case of clear notion of

the fact that circuit is supplied to all electrical components (lamps, electric motor and the
like) from the AB 

от  АКБ

 by wires through the switches, relays, fuses, fusible elements,

and then goes back to the AB through the tractor “ground”. Any problems related to the
failure of the electrical equipment can be determined by stopping of the electric current
supply from AB or current return to the AB.

Note. The information specified in the present subsection 7.4 “Possible failures in

the electrical equipment and guidelines for troubleshooting” shall be used during trouble-
shooting of the gearbox electronic control system, rear axle differential lock, front driving
axle drive, front and rear power take-off shafts (Annex C) and partially during troubleshoot-
ing of the engine electronic control system  (Annex B).

https://tractormanualz.com/

Summary of Contents for 3522.5





















































































































































































































































































































































Reviews:

No comments

Related manuals for 3522.5

LANDINI 5860 Operation And Maintenance Manual preview
5860
Brand: LANDINI Pages: 132
LS tractor MT230E 2020 Operator'S Manual preview
MT230E 2020
Brand: LS tractor Pages: 218
FENDT FAVORIT 900 Workshop Manual preview
FAVORIT 900
Brand: FENDT Pages: 1245
BCS DUPLEX GOLD Owner'S Manual preview
DUPLEX GOLD
Brand: BCS Pages: 34
Washtech TCW-7055 Installation & Maintenance Manual preview
TCW-7055
Brand: Washtech Pages: 30
Curtis 1KB17AS1 Installation & Owner'S Manual preview
1KB17AS1
Brand: Curtis Pages: 10
Hagie UpFront STS 10T Operator'S Manual preview
UpFront STS 10T
Brand: Hagie Pages: 93
Colombia PS15B97 Instruction Manual preview
PS15B97
Brand: Colombia Pages: 72
Belarus 510 Operating Manual preview
510
Brand: Belarus Pages: 125
GOLDONI FH0250 Operation And Maintenance preview
FH0250
Brand: GOLDONI Pages: 145
Winton WFM Series Owner'S Manual preview
WFM Series
Brand: Winton Pages: 24
Ventrac KP540 Operator'S Manual preview
KP540
Brand: Ventrac Pages: 41
SpeedEPart Agri-Fab 45-0302 Owner'S Manual preview
Agri-Fab 45-0302
Brand: SpeedEPart Pages: 8
Field Tuff FTF-2GBF4S Owner'S Manual preview
FTF-2GBF4S
Brand: Field Tuff Pages: 4
Belle Group BMD 300 Operator'S Manual preview
BMD 300
Brand: Belle Group Pages: 200
Trac Vac 858-RH Operating And Assembly Manual preview
858-RH
Brand: Trac Vac Pages: 9
HE-VA King-Roller Operating Instructions Manual preview
King-Roller
Brand: HE-VA Pages: 56
Case IH PUMA CVX 150 Quick Instruction preview
PUMA CVX 150
Brand: Case IH Pages: 24

Brands by name

Popular brands

Load more brands