background image

(3)  Remove  the  four  screws,  lockwashers,  and  flat  washers 

that  secure  the  tape  winder  assembly  to  the  frame  of 

the  stand. 

( 4)  Remove  tape  winder  assembly. 

2.11 

Clutch  Shaft  Assembly 

(1)  Remove  the  drive-shaft-gear-hub  mounting  screw  and 

lockwasher. 

(2)  Remove  the  drive  shaft  gear  and  hub. 
(3)  Remove  the  drive  shaft  belt. 
(4)  Unhook  the  stoplever  spring. 

(5) 

Remove  the  two  screws,  lockwashers,  and  flat  washers 

that  secure  the  drive-shaft  gear  bracket  to  the  tape­

winder  support  bracket. 

(6) 

Remove  the  drive-shaft  gear  bracket  with  the  stoplever 

attached. 

(7)  Remove  the  two  screws,  lockwashers,  and  flat  washers 

that  secure  the  outer  clutch  bearing  bracket  to  the 

outer  plate. 

(8)  Remove  the  outer  clutch  bearing  bracket. 
(9)  Remove  the  two  screws,  lockwashers,  and  flat  washers 

that  secure  the  inner  bearing  plate  to  the  outer  plate. 

(10)  Remove  the  clutch  shaft  assembly. 

3. 

ASSOCIATED  BELL  SYSTEM  PRACTICES 

3.01 

The  following  Bell  System  Practices  provide  additional 

information  that  may  be  required  for  use  with  this 

section. 

General  Information  and  Routines  for  Disas­

sembling 

and 

Reassembling 

Teletypewriter 

Section 

Apparatus 

P30.013 

General  Requirements  and  Adjusting  Procedures 

for  Teletypewriter  Apparatus 

P30.012 

Preparation  of  Teletypewriter  Apparatus  for 

Installation 

P33.014 

Teletypewriter  Tools  and  Maintenance  Supplies 

P30.301 

Alphabetical  Index  of  28-type  Equipment,  Bell 

System  Practices  and  Associated  28  ASR 

Station  Drawings 

P34.001 

28 REPERF-TRANS SET, 

UNIT, AND STAND 

DIS· 

P34.42Q 

ASSEMBLY 

Page 5 

ANDRE· 

c.  p.., ........ 

AC::IO:�MRI  V 

Summary of Contents for 28







Reviews: